10.1inch HDMI LCD (B) (with case)

10.1inch HDMI LCD (B) (with case) 1280 × 800, IPS IPS, 1280 × 800, 10.1 inch Capacitive Touch Screen LCD, Supports Multi mini-PCs, Multi Systems

{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

{{{name6}}}

Primary Attribute Category: OLEDs / LCDs, LCD, Raspberry Pi LCD {{{userDefinedInfo}}}: {{{userdefinedvalue}}} Brand: Waveshare

Website International: Website Chinese: 官网

Onboard Interfaces USB HDMI

Related Products 15.6inch HDMI LCD (H) (with case) 15.6inch HDMI LCD (H) 15.6inch FHD Monitor 13.3inch HDMI LCD (H) (with case) V2 13.3inch HDMI LCD (H) (with case) 13.3inch HDMI LCD (H) 13.3inch Magic Mirror 13.3inch Magic Mirror C4 13.3inch PiPad 13.3inch PiPad C4 12.5inch FHD Monitor 11.6inch HDMI LCD (H) (with case) 11.6inch HDMI LCD (H) 11.9inch HDMI LCD 10.5inch HDMI AMOLED 10.1inch HDMI LCD 10.1inch HDMI LCD (B) (with case) 10.1inch HDMI LCD (E) 10.1inch HDMI LCD (G) (with case) 10.1inch HDMI LCD (H) (with case) 10.1HP-CAPQLED 9inch 2560x1600 Monitor 9HP-CAPQLED 8.8inch Side Monitor 8inch DSI LCD 8inch DSI LCD (with cam) 7.9inch HDMI LCD 7inch FHD Monitor 7inch HDMI LCD (H) (with case) 7inch HDMI LCD (C) 7inch HDMI LCD (B) 7inch HDMI LCD 7inch DPI LCD 7HP-CAPQLED 7inch DSI LCD 7inch DSI LCD (with cam) 7inch DSI LCD (with case A) 7inch DSI LCD (C) 6inch HDMI AMOLED 5inch HDMI LCD (H) 5inch HDMI LCD (H) V4 5inch HDMI LCD (G) 5inch HDMI LCD (B) 5inch HDMI LCD 5inch HDMI AMOLED 5inch DPI LCD 5inch DSI LCD 5.5inch HDMI AMOLED 4inch HDMI LCD (C) 4inch DSI LCD 4.3inch HDMI LCD (B) 4.3inch DSI LCD 4inch DSI LCD 4inch DPI LCD (B) 4inch DPI LCD (C) 4inch HDMI LCD (H) 4inch HDMI LCD 4inch RPi LCD (C) 4inch RPi LCD (A) 3.5inch DPI LCD 3.5inch HDMI LCD 3.5inch RPi LCD (C) 3.5inch RPi LCD (B) 3.5inch RPi LCD (A) 3.2inch HDMI LCD (H) 3.2inch RPi LCD (B) 2.8inch HDMI LCD (H) 2.8inch DPI LCD 2.8inch RPi LCD (A) 2.23inch OLED HAT 1.3inch OLED HAT 1.3inch LCD HAT 1.44inch LCD HAT 1.8inch LCD Module EINK-DISP-103 LCD1602 RGB Module Pico-Clock-Green Pico-RGB-Matrix-P3-64x32 RGB-Matrix-P3-64x32

Overview

Introduction

• 10.1-inch IPS screen, hardware resolution is 1280 × 800.
• 10-point capacitive touch control, tempered glass panel, hardness up to 6H.
• When used with Raspberry Pi, supports Raspberry Pi OS / Ubuntu / Kali and Retropie.
• When used as a computer monitor, supports Windows 11/10/8.1/8/7.

Video

EDID Sequence Parameter

If the main control board's system can automatically recognize EDID for display, there is no need to configure additional timing parameters.
Otherwise, you can refer to the following EDID settings:

Pixel Clock	H Adressable	H Blanking	V Adressable	V Blanking	H Front Porch	H Sync Width	V Front Porch	V Sync Width	H Image Size	V Image Size	H Border	V Border
75.00	1280	128	800	45	40	48	13	3	108	68	0	0

Working with PC

This Support PC version Windows 11/10/8.1/8/7 system.

Instructions:

1. Connect the Power Only port of the touch screen to a 5V power adapter.
2. Use a type A to micro USB cable to connect the Touch interface of the touch screen and any USB interface of the PC.
3. Connect the touch screen and the HDMI port of the PC with an HDMI cable. After about a few seconds, you can see the LCD display normally.

• Note 1: Please pay attention to connecting cables in order, otherwise it may not display properly.
  
• Note 2: When the computer is connected to multiple monitors at the same time, the cursor on the main monitor can only be controlled through this LCD, so it is recommended to set this LCD as the main monitor.
  

Working with Raspberry Pi

Software setting

Supports Raspberry Pi OS / Ubuntu / Kali and Retropie systems on Raspberry Pi.

Please download the latest version of the image from the Raspberry Pi official website.

1. Download the compressed file to the PC, and extract the img file.
2. Connect the TF card to the PC and use SDFormatter to format the TF card.
3. Open the Win32DiskImager software, select the system image prepared in step 1, and click write to burn the system image.
4. After the programming is completed, open the config.txt file in the root directory of the TF card, add the following code at the end of config.txt and save it

hdmi_group=2
hdmi_mode=87
hdmi_cvt 1280 800 60 6 0 0 0
hdmi_drive=1

Backlight Adjustment

wget https://files.waveshare.com/upload/0/01/Brightness-HDMI.zip
unzip Brightness-HDMI.zip
cd Brightness-HDMI
sudo chmod +x install.sh
./install.sh

#lite version Enter the lite directory:
#cd lite
#./Raspi_USB_Backlight_nogui -b X
# X range is 0~10, 0 is the darkest, 10 is the brightest.
#For example: ./Raspi_USB_Backlight_nogui -b 3

Note: Only the Rev4.1 version supports the USB dimming function.

Hardware connection

1. The Power Only interface of the touch screen is connected to a 5V power adapter.
2. Connect the touch screen to the HDMI port of the Raspberry Pi with an HDMI cable.
3. Use a type A to micro USB cable to connect the Touch interface of the touch screen to any USB interface of the Raspberry Pi.
4. Insert the TF card into the TF card slot of the Raspberry Pi, power on the Raspberry Pi, and wait for more than ten seconds to display normally.

Resource

Document

• 10.1inch-HDMI-LCD-B-with-Holder-assemble.jpg
• 10.1inch HDMI LCD (B) Display Area
• 10.1inch HDMI LCD (B) 3D drawing
• CE RoHs certification information
• Raspberry Pi LCD PWM Backlight Control

Note: Under normal circumstances, we do not recommend customers modify the hardware by themselves. Modifying the hardware without permission may cause the product to be out of warranty. Please be careful not to damage other components when modifying.

Software

• putty
• Panasonic_SDFormatter-SD card formatting software
• Win32DiskImager-Burn image software

FAQ

Question:After using the LCD for a few minutes, there are black shadows on the edges?

 Answer:

• This may be due to the customer turning on the option for hdmi_drive in config.txt

• The method is to comment out this line and reboot the system. After rebooting, the screen may not be fully recovered, just wait a few minutes (sometimes it may take half an hour, depending on the time of operation under abnormal conditions).

Question:Using the LCD to connect to the PC, the display cannot be displayed normally, how can I solve it?

 Answer:

• Make sure that the HDMI interface of the PC can output normally.
• PC only connects to LCD as display device, not to other monitors.
• Connect the power cable first and then the HDMI cable.
• Some PCs also need to be restarted to display properly.

Question:Connected to a PC or other non-designated mini PC, using Linux system, how to use the touch function?

 Answer:

You can try compiling the general touch driver "hid-multitouch" into the kernel, which generally supports touch.

Question:What is the working current of the 10.1inch HDMI LCD (B)?

 Answer:

Using a 5V power supply, the working current of the backlight is about 750mA, and the working current of the backlight is about 300mA.

Question:How can I adjust the backlight of the 10.1inch HDMI LCD (B)?

 Answer:

Remove the resistor as shown below, and connect the PWM pad to the P1 pin of the Raspberry Pi.
Execute the following command in the Raspberry Pi terminal:

gpio -g pwm 18 0
gpio -g mode 18 pwm （the occupied pin is the PWM pin）
gpio pwmc 1000
gpio -g pwm 18 X （X value in 0~1024），0 represents the brightest， and 1024 represents the darkest.

{{{5}}}

Question:How to install the bracket for the screen bottom plate?

 Answer:

Support

Technical Support

If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. Please be patient as we make every effort to help you to resolve the issue.
Working Time: 9 AM - 6 PM GMT+8 (Monday to Friday)

Submit Now