PCIe TO MiniPCIe GbE USB3.2 HAT+

From Waveshare Wiki
Jump to: navigation, search
PCIe TO MiniPCIe GbE USB3.2 HAT+
PCIe TO MiniPCIe GbE USB3.2 HAT+.jpg

PCIe TO MiniPCIe GbE USB3.2 Gen1
{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

{{{name6}}}

Overview

Introduction

This adapter board supports converting the PCIe interface to USB3.2, MiniPCIe and Gigabit ETH, designed for Raspberry Pi 5. It is compatible with multiple MiniPCIe 4G modules or MiniPCIe devices, supports Gen2 mode and high-speed communication.

Features

  • Designed for Raspberry Pi 5, with HAT+ standard, onboard I2C EEPROM, and support 40pin GPIO header for stacking and expansion.
  • Support PCI-E×1 Gen2 mode.
  • Onboard 2-ch USB 3.2 Gen1 high-speed interface, for connecting to more peripheral devices, support PCIe to expand USB3.2 MiniPCIe interface, high-speed communication, with lower latency.
  • Onboard MiniPCIe interface, support MiniPCIe 4G modules such as SIM7600G-H-PCIE and EG25-G mPCIe.
  • Expand driver-free Gigabit Ethernet port.
  • Onboard Type-C interface for 4G networking, debugging, firmware update on PC, or for external power input.
  • Onboard power monitoring chip for real-time monitoring of voltage, current and power parameters.
  • Onboard SIM card slot for inserting Nano-SIM card.
  • Onboard reset key, power and network indicator for debugging and checking module working status.

MiniPCIe Support List

1. SIM7600G-H-M.2
2. EG25-G mPCIe
3. 2-CH_CAN_MiniPCIe

Dimensions

PCIe-TO-MiniPCIe-GbE-USB3.2-HAT-Plus-details-size.jpg

User Guide

Hardware Connection

Please pay attention to the cable orientation as shown below:
PCIe-TO-MiniPCIe-GbE-USB3.2-HAT-Plus-details-5.jpg

How to Use

1: Enable PCIE interface:

As the PCIE interface is not enabled on the Raspberry Pi 5 by default, you can add the following content to enable it at /boot/firmware/config.txt:
dtparam=pciex1

2: Reboot PI5 after modification, and the device can be recognized.

As shown below, the VL805 is recognized as our device, and the other PI5 is the RPI chip.
PCIe TO Gigabit ETH USB3.2 HAT+-1-1.png

3: Execute "lsusb" to the USB device that has been recognized.

PCIe TO Gigabit ETH USB3.2 HAT+-1-2.png

DIP Switch Control

The onboard module dial-up switch can be connected to GPIO6 of the Raspberry Pi, you can switch it on to use the Raspberry Pi to control the module to reset or power on/off. (It is switched off by default (recommended). The board status is up to the Raspberry Pi, for example, if the Raspberry Pi shuts down, the board would power off.)
Onboard dial-up switch for switching MiniPCIe USB connection, and you can select the connected Raspberry Pi through dial-up switch mode:

How to Install and Use Dial-up Tool (Required for module usage)

Input the following commands to install waveshare-CM dial-up tool:

wget -O - https://files.waveshare.com/wiki/PCIe-TO-4G-5G-M.2-USB3.2-HAT-Plus/install.sh | sudo bash

After installation, if it cannot automatically dial up with NDIS(qmi) and MBIM, you can use the dial-up tool for network. YOUR_APN is the APN of the used SIM card:

sudo waveshare-CM
# or
sudo waveshare-CM -s YOUR_APN

NVME Power Monitoring

The onboard INA219 chip can detect the voltage and current, easy to monitor the device status and monitor the input 5V voltage status (not 3.3V).
The default I2C address is 0x40, addresses can be modified via back resistors to support stacking of different expansion boards.

Demo:

wget https://files.waveshare.com/wiki/PCIe-TO-M.2-HAT%2B/PCIe_TO_M.2_HAT%2B.zip
unzip -o PCIe_TO_M.2_HAT+.zip -d ./PCIe_TO_M.2_HAT+
cd PCIe_TO_M.2_HAT+
sudo python INA219.py
PCIe TO M.2 HAT+ W 8.png

Ethernet (ETH) Port Usage

1: Reboot the PI5, and then it can recognize the device.

As shown below, the identified RTL8111 is our device, and the other one is the RPI chip for PI5  
PCIe-TO-Gigabit-ETH-USB-3.2-Gen1-HAT-Plus-1-7.png

2: Execute "ifconfig", and you can see the network card is recognized.

PCIe-TO-Gigabit-ETH-USB-3.2-Gen1-HAT-Plus-1-8.png

3: Use ping command to test:

ping baidu.com -I eth1
#-I specifies the Ethernet port  
PCIe-TO-Gigabit-ETH-USB-3.2-Gen1-HAT-Plus-1-3.png

Resource

Datasheet

INA219

SIM7600G-H-PCIE

EG25-G mPCIe

Driver Files

SIM7600G-H-PCIE

EG25-G mPCIe

Imager

Openwrt

Support



Technical Support

If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. Please be patient as we make every effort to help you to resolve the issue.
Working Time: 9 AM - 6 PM GMT+8 (Monday to Friday)