For Bullseye 64-bit System

Install Imager

Please download the bullseye imager 64-bit from Raspberry Pi website.
1) Download it on the PC and unzip it to get the ".img" file.
2) Connect the TF card to the PC, open Win32DiskImager.exe software, select the system image downloaded in step 1, and click "Write" to write the system image. Then, open the TF card file folder.
3) Download and unzip the waveshare32b.dtbo device tree file to add it to the /boot/overlay folder.
4) Connect the TF card to the Raspberry Pi, boot the Raspberry Pi, and log in to the Raspberry Pi terminal (you can connect the Raspberry Pi to the HDMI display or use SSH to remotely login).

Configure Driver File

Open the "config.txt" file under the boot directory, comment out "dtoverlay=vc4-kms-v3d", and add the following at the end of [all]:

dtparam=spi=on
dtoverlay=waveshare32b

hdmi_force_hotplug=1
max_usb_current=1
hdmi_group=2
hdmi_mode=87
hdmi_cvt 480 320 60 6 0 0 0
hdmi_drive=2
display_rotate=0

Config Touch

Add the following codes in the terminal:

sudo apt-get install xserver-xorg-input-evdev 
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
sudo apt-get install xinput-calibrator
sudo nano /usr/share/X11/xorg.conf.d/99-calibration.conf

Add the following content in 99-calibration.conf file:

Section "InputClass"
        Identifier      "calibration"
        MatchProduct    "ADS7846 Touchscreen"
        Option  "Calibration"   "3932 300 294 3801"
        Option  "SwapAxes"      "1"
        Option "EmulateThirdButton" "1"
        Option "EmulateThirdButtonTimeout" "1000"
        Option "EmulateThirdButtonMoveThreshold" "300"
EndSection

FBCP Porting

Network is required for this step:

sudo apt-get install cmake
wget  https://files.waveshare.com/upload/1/1e/Rpi-fbcp.zip
unzip Rpi-fbcp.zip
cd rpi-fbcp/
mkdir build
cd build/
cmake ..
make
sudo install fbcp /usr/local/bin/fbcp

Set Auto-start

sudo nano /etc/rc.local

Add the following codes before "exit 0":

sleep 7
fbcp &

sudo reboot

Reboot it, and the screen displays normally.

For Bookworm System

For Raspberry Pi 4 & Raspberry Pi 5

Download and Compile fbcp

Open the Raspberry Pi terminal and execute:

sudo apt install libraspberrypi-dev -y
sudo apt-get install unzip -y
sudo apt-get install cmake -y
sudo wget https://files.waveshare.com/upload/c/c3/Waveshare32b.zip
sudo unzip ./Waveshare32b.zip
sudo cp Waveshare32b.dtbo /boot/overlays/
sudo wget https://files.waveshare.com/upload/1/1e/Rpi-fbcp.zip
sudo unzip ./Rpi-fbcp.zip
cd rpi-fbcp/
sudo rm -rf build
sudo mkdir build
cd build
sudo cmake ..
sudo make -j4
sudo install fbcp /usr/local/bin/fbcp

Edit "config.txt" file:

sudo nano /boot/firmware/config.txt

Blocking the following sentence:

Add the following code at the end of config.txt:

dtparam=spi=on
dtoverlay=waveshare32b
hdmi_force_hotplug=1
max_usb_current=1
hdmi_group=2
hdmi_mode=1
hdmi_mode=87
hdmi_cvt 480 320 60 6 0 0 0
hdmi_drive=2
display_rotate=0

Set Auto-start startx and fbcp

Open ".bash_profile". If there is no ".bash_profile" file, you can create one:

sudo nano ~/.bash_profile

Add the following code at the bottom of ".bash_profile" file:

if [ "$(cat /proc/device-tree/model | cut -d ' ' -f 3)" = "5" ]; then
    # rpi 5B configuration
    export FRAMEBUFFER=/dev/fb1
    startx  2> /tmp/xorg_errors
else
    # Non-pi5 configuration
    export FRAMEBUFFER=/dev/fb0
    fbcp &
    startx  2> /tmp/xorg_errors
fi

Open the "99-fbturbo.~" file, if it exists, you need to check fb is "fb0":

sudo nano /usr/share/X11/xorg.conf.d/99-fbturbo.~

Add the following code in "99-fbturbo.~" file:

Section "Device"
        Identifier      "Allwinner A10/A13 FBDEV"
        Driver          "fbturbo"
        Option          "fbdev" "/dev/fb0"

        Option          "SwapbuffersWait" "true"
EndSection

Set CLI Auto-login

sudo raspi-config nonint do_boot_behaviour B2
sudo raspi-config nonint do_wayland W1
sudo reboot

After rebooting, the main screen can normally display.
Note 1: Please ensure the username of the Raspberry Pi is "pi", otherwise, it cannot automatically log in.
Note 2: After setting the above configuration, it may take a while to reboot the system and load SSH.

Configure Touch

Install calibrator software:

sudo apt-get install xserver-xorg-input-evdev 
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
sudo apt-get install xinput-calibrator

Edit 99-calibration.conf configuration file:

sudo nano /usr/share/X11/xorg.conf.d/99-calibration.conf

Add the following content to the "99-calibration.conf" configuration file:

Section "InputClass"
        Identifier      "calibration"
        MatchProduct    "ADS7846 Touchscreen"
        Option  "Calibration"   "171 3795 3913 168"
        Option  "SwapAxes"      "1"
EndSection

Reboot to take effect.

sudo reboot

Configure Camera

Edit config.txt file

sudo nano /boot/firmware/config.txt

Add the following code at the end of the config.txt

dtoverlay=vc4-kms-v3d
max_framebuffers=2

Edit the 98-spi-screen.conf configuration file

sudo nano /etc/X11/xorg.conf.d/98-spi-screen.conf

Add the following to the 98-spi-screen.conf configuration file

Section "Device"
Identifier "SPI Screen" 
Driver "fbdev"
Option "fbdev" "/dev/fb0"
EndSection

Reboot to take effect

sudo reboot

Turn on the camera:

libcamera-hello --qt-preview

For All Raspberry Pi Versions

The operation must be based on bookworm-lite system: 64-bit lite, 32-bit lite

Download Needed Software

Update system:

sudo apt update && sudo apt upgrade && sudo apt full-upgrade -y

Install xorg service:

sudo apt-get install --no-install-recommends xserver-xorg -y
sudo apt-get install --no-install-recommends xinit -y

Install Desktop Manager:

sudo apt install lightdm -y

Install Raspberry Pi official GUI:

sudo apt install raspberrypi-ui-mods -y

Install browser (optional):

sudo apt install chromium-browser -y

Download Driver

Open the Raspberry Pi terminal and execute:

sudo apt install libraspberrypi-dev -y
sudo apt-get install unzip -y
sudo apt-get install cmake -y
sudo wget https://files.waveshare.com/upload/c/c3/Waveshare32b.zip
sudo unzip ./Waveshare32b.zip
sudo cp waveshare32b.dtbo /boot/overlays/
sudo wget https://files.waveshare.com/upload/1/1e/Rpi-fbcp.zip
sudo unzip ./Rpi-fbcp.zip
cd rpi-fbcp/
sudo rm -rf build
sudo mkdir build
cd build
sudo cmake ..
sudo make -j4
sudo install fbcp /usr/local/bin/fbcp

Edit config.txt file:

sudo nano /boot/config.txt

Block the following sentences:

Add the following codes at the end of "config.txt":

dtparam=spi=on
dtoverlay=waveshare32b
hdmi_force_hotplug=1
max_usb_current=1
hdmi_group=2
hdmi_mode=87
hdmi_cvt 640 480 60 6 0 0 0
hdmi_drive=2
display_rotate=0

Set Auto-start startx and fbcp

Open ".bash_profile". If there is not ".bash_profile" file, you can create one:

sudo nano ~/.bash_profile

Add the following code at the bottom of ".bash_profile" file:

if [ "$(cat /proc/device-tree/model | cut -d ' ' -f 3)" = "5" ]; then
    # rpi 5B configuration
    export FRAMEBUFFER=/dev/fb1
    startx  2> /tmp/xorg_errors
else
    # Non-pi5 configuration
    export FRAMEBUFFER=/dev/fb0
    fbcp &
    startx  2> /tmp/xorg_errors
fi

Open the "99-fbturbo.~" file, if it exists, you need to check fb is "fb0":

sudo nano /usr/share/X11/xorg.conf.d/99-fbturbo.~

Add the following code in "99-fbturbo.~" file:

Section "Device"
        Identifier      "Allwinner A10/A13 FBDEV"
        Driver          "fbturbo"
        Option          "fbdev" "/dev/fb0"

        Option          "SwapbuffersWait" "true"
EndSection

Set CLI Auto-login

sudo raspi-config nonint do_boot_behaviour B2
sudo raspi-config nonint do_wayland W1
sudo reboot

After rebooting, the main screen can normally display.
Note 1: Please ensure the username of the Raspberry Pi is "pi", otherwise, it cannot automatically log in.
Note 2: After setting the above configuration, it may take a while to reboot the system and load SSH.

Configure Touch

Install calibrator software:

sudo apt-get install xserver-xorg-input-evdev 
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
sudo apt-get install xinput-calibrator

Edit "99-calibration.conf" file:

sudo nano /usr/share/X11/xorg.conf.d/99-calibration.conf

Add the following content to "99-calibration.conf" file:

Section "InputClass"
        Identifier      "calibration"
        MatchProduct    "ADS7846 Touchscreen"
        Option  "Calibration"   "171 3795 3913 168"
        Option  "SwapAxes"      "1"
EndSection

Reboot it to take effect:

sudo reboot

Navigation menu

3.2inch RPi LCD (B) Manual Configuration

Contents

For Bullseye 64-bit System

Install Imager

Configure Driver File

Config Touch

FBCP Porting

Set Auto-start

For Bookworm System

For Raspberry Pi 4 & Raspberry Pi 5

Download and Compile fbcp

Set Auto-start startx and fbcp

Set CLI Auto-login

Configure Touch

Configure Camera

For All Raspberry Pi Versions

Download Needed Software

Download Driver

Set Auto-start startx and fbcp

Set CLI Auto-login

Configure Touch