- Description
Details
Feel free to contact us if you need to change to other module, refer to the table below and the supported bands according to your local service provider.
| LTE Cat 6 | EM06-E | EM06-J | EM06-A |
|---|---|---|---|
| Region / Provider | EMEA/APAC/Brazil | Japan | North America/Mexico |
Supports LTE-A and UMTS/HSPA(+) multi networks
multi-constellation high-accuracy GNSS, cloud platform communication, LTE-A networking
This is an LTE Cat 6 Raspberry Pi communication HAT with GNSS and up to 300Mbps (downlink) / 50Mbps (uplink) data rate. It is applicable for countries/regions including Europe, the Middle East, Africa, Asia-Pacific, Brazil... By connecting it to PC, Raspberry Pi or Jetson Nano host boards, it is easy to enable LTE-A high speed networking, cloud platform communication, SMS, and global GNSS positioning functions.
- Multi-constellation high-accuracy GNSS positioning: GPS, GLONASS, BeiDou/Compass, Galileo, QZSS
- Integrates extensive network protocols, with multi drivers and software support, compatible with different OS including Windows / Linux / Android
- USB 3.1 port (USB 2.0 compatible) for connecting to PC, Raspberry Pi, or Jetson Nano host board to enable high speed LTE-A communication
- Standard M.2 B KEY slot, compatible with QUECTEL and SIMCOM series 4G/5G M.2 modules
- Onboard PWR and RST control pin, enabled via DIP switch, for connecting to external IO to turn on/off or reset the module
- Onboard USB-C connector, enabled via switch, for connecting standalone power supply for the module, allows more loads, stable amd flexible power supply
- Onboard power supply on/off switch, reset button and LED indicator, easy to turn on/off the module or monitor the operating status
- Reserved 4x SMA to IPEX antenna connectors, easy to install and change the SMA antenna positions
- High efficiency power supply circuit, up to 3A output current
| LTE Cat 6 | |
|---|---|
| Region / Provider | EMEA / APAC (except Japan and CMCC) / Brazil |
| Module dimensions | 42.0 × 30.0 × 2.3 (mm) |
| Temperature range | |
| Operating temperature | -30°C ~ +70°C |
| Extension temperature | -40°C ~ +85°C |
| Frequency band | |
| LTE-FDD | B1, B3, B5, B7, B8, B20, B28, B32 (receive only for B32) |
| LTE-TDD | B38, B40, B41 |
| 2xCA | B1+B1, B5, B8, B20, B28; B3+B3, B5, B7, B8, B20, B28; B7+B5, B7, B8, B20, B28; B20+B32 (B32 is used for aux component carrier only), B38+B38, B40+B40, B41+B41 |
| WCDMA | B1, B3, B5, B8 |
| GNSS | GPS/GLONASS/BeiDou (Compass)/Galileo/QZSS |
| Data rate | |
| LTE-FDD | 300 Mbps (DL) / 50 Mbps (UL) |
| LTE-TDD | 226 Mbps (DL) / 28 Mbps (UL) |
| DC-HSPA+ | 42 Mbps (DL) / 5.76 Mbps (UL) |
| WCDMA | 384 Kbps (DL) / 384 Kbps (UL) |
supports LTE-A and UMTS/HSPA(+) multi networks
applicable for countries/regions including Europe, the Middle East, Africa, Asia-Pacific, Brazil...
supports Windows / Linux / Android...
Just plug it into USB port, go through some simple configuration, the high speed LTE-A network connection will be ready to use
for Windows PC or Jetson Nano series, use a USB cable
for Raspberry Pi 4B/3B+, or CM4-IO-BASE-A/B, use the purpose-made USB adapter
supports GPS, GLONASS, BeiDou/Compass, Galileo, QZSS
compatible with Raspberry Pi series and Jetson Nano, stackable design for more HATs
better heat dissipation for both Raspberry Pi and the LTE-A module
Compatible with EM06-E, EM06-J, EM06-A series modules
| LTE Cat 6 | EM06-E | EM06-J | EM06-A |
|---|---|---|---|
| Region / Provider | EMEA/APAC①/Brazil | Japan | North America/Mexico |
| Operating temperature | -30 °C ~ +70 °C | ||
| Extension temperature | -40 °C ~ +85 °C | ||
| Dimensions | 42.0 × 30.0 × 2.3 (mm) | ||
| Power supply | 3.135V~4.4V, typical 3.7V | ||
| Power consumption | 50μA @ shutdown 4.1mA @ hibernate, typical 22.1mA @ idle |
47μA @ shutdown 3.8mA @ hibernate, typical 19.5mA @ idle |
50μA @ shutdown 3.8mA @ hibernate, typical 21.3mA @ idle |
| Frequency band | |||
| LTE-FDD | B1, B3, B5, B7, B8, B20, B28, B32② | B1, B3, B8, B18, B19, B26, B28 | B2, B4, B5, B7, B12, B13, B25, B26, B29②, B30, B66 |
| LTE-TDD | B38, B40, B41 | B41 | B41 |
| 2xCA | B1+B1, B5, B8, B20, B28; B3+B3, B5, B7, B8, B20, B28; B7+B5, B7, B8, B20, B28; B20+B32②; B38+B38; B40+B40; B41+B41 |
B1+B1, B8, B18, B19, B26, B28; B3+B3, B8, B18, B19, B26, B28; B41+B41 |
B2+B2, B5, B12, B13, B29②; B4+B4, B5, B12, B13, B29②; B7+B5, B7, B12, B26; B25+B5, B12, B25, B26; B30+B5, B12, B29②; B66+B5, B12, B13, B29②, B66; B41+B41 |
| WCDMA | B1, B3, B5, B8 | B1, B3, B6, B8, B19 | B2, B4, B5 |
| GNSS | GPS / GLONAS S/ BeiDou (Compass) / Galileo / QZSS (configurable) | ||
| Data rate | |||
| LTE-FDD | 300 Mbps (DL); 50 Mbps (UL) | ||
| LTE-TDD | 226 Mbps (DL); 28 Mbps (UL) | ||
| DC-HSPA+ | 42 Mbps (DL); 5.76 Mbps (UL) | ||
| WCDMA | 384 kbps (DL); 384 kbps (UL) | ||
|
① except Japan and CMCC; ② B29/B32 is only used for receiving in LTE-FDD, while only for aux component carrier wave in 2×CA; |
|||
- Raspberry Pi GPIO header
for connecting with Raspberry Pi - DIP switches
Enables the power control and reset pins - M.2 slot
Compatible with most SIMCom and QUECTEL 4G/5G modules in M.2 form factor - SIM card slot 1
one of the 2x SIM card slots, dual card single standby - USB3.1 port
USB 2.0 compatible, for connecting with different hosts - USB Type-C port
5V 3A input, stable and flexible power supply
- Audio jack
SIM7600X/SIM8XXX series supports audio function, but RM5XX/EM06XX series temporarily does not support this function - Antenna connector
Supports quad antennas - Reset button
- Power supply switch
Switch the power supply mode:
When set to USB, the module is powered via the "5. USB3.1 port"
When set to EXT PWR, the module is powered by the external power supply via the "6. USB Type-C port" - Indicator
Easy to monitor the operating status of module
- Cooling fan
Better heat dissipation for both Raspberry Pi and the 5G module - SIM card slot 2
Switchable via AT command - Module settings switch
Switch A to ON for SIM7600X/A7906X/SIM7906X/SIM7912X series 4G M.2 modules;
Switch B to ON for SIM8202X/SIM8200EA/SIM8262X series 5G M.2 modules;
Switch C to ON for RM50X/RM520N-GL/EM06X series 5G/LTE-A M.2 modules
- USB 2.0 interface pads
- NAU8810X Audio Chip
For SIM7600X/SIM8XXX series modules, RM5XX and EM06XX series modules temporarily does not support this function - Fan Header
5V cooling fan power supply
LTE-A Wireless Router
Combined with OpenWrt, turns the Raspberry Pi into a LTE-A wireless router, providing WiFi hotspot for smartphones to easily access the LTE-A Network.
LTE-A Live Streaming
While mounting an additional camera, it is able to do live streaming on webpage or live platform through ffmpeg video stream.
Weight: 0.204 kg
Quick Overview
- M.2 TO 4G/5G HAT x1
- EM06-E x1
- Antenna 2pcs x1
- IPEX adapter cable 2pcs x1
- 2*20PIN pin header x1
- Passive GPS antenna x1
- Dual plug USB3.0 cable x1
- USB3.0 adapter x1
- USB2.0 adapter x1
- SMA protective cap 2pcs x1
- Screws pack x1
