- Description
Details
4G/3G/2G communication and GNSS positioning, global band
This is a 4G/3G/2G Raspberry Pi communication HAT with GNSS positioning and high speed LTE CAT4 global band connection. By connecting it to PC, Raspberry Pi or Jetson Nano host boards, it is easy to enable 4G high speed networking, cloud platform communication, phone call/SMS, and global GNSS positioning functions.
- Supports dial-up, phone call, SMS, TCP, UDP, MQTT, HTTP(S), FTP(S), and so on
- GNSS positioning: GPS, Beidou, Glonass, Galileo, QZSS, LBS base station
- USB 3.1 port (USB 2.0 compatible) for connecting to PC, Raspberry Pi, or Jetson Nano host board to enable high speed 4G communication
- Onboard UART, PWR, and RST control pin, built-in voltage level translator, enabled via DIP switch, for use with hosts like Raspberry Pi or Arduino
- Onboard USB-C connector, enabled via switch, for connecting standalone power supply for the module, allows more loads, stable amd flexible power supply
- Onboard power supply on/off switch, reset button and LED indicator, easy to turn on/off the module or monitor the operating status
- Reserved 4x SMA to IPEX antenna interfaces, with pre-soldered 2x connectors for easily using antennas, allows changing the SMA antenna position
- Onboard audio jack and audio decoder, allows audio operation like making phone call
- High efficiency power supply circuit, up to 3A output current
| Frequency band | |
|---|---|
| LTE Cat-4 | LTE-FDD: B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B66 LTE-TDD: B34, B38, B39, B40, B41 |
| 3G | UMTS/HSDPA/HSPA+: B1, B2, B4, B5, B6, B8, B19 |
| 2G | GSM/GPRS/EDGE: 850, 900, 1800, 1900 MHz |
| GNSS | |
| Satellite systems | GPS, Beidou, GLONASS, GALILEO, QZSS |
| Receiver type | 16-channel |
| C/A Code | |
| Sensitivity | -159 dBm (GPS) / -158 dBm (GLONASS) / TBD (BeiDou) |
| Cold starts: -148 dBm | |
| Time-To-First-Fix (open air) | Cold starts: <35s |
| Hot starts: <1s | |
| SMS and Audio | |
| SMS | Supported types: MT, MO, CB, Text, PDU |
| Storage: USIM card and ME (default) | |
| Audio feature | Supports echo cancellation |
| Supports noise reduction | |
LTE Cat-4: up to 150Mbps (downlink) / 50Mbps (uplink)
3G (HSPA+): up to 42Mbps (downlink) / 5.76Mbps (uplink)
2G (GPRS/EDGE): up to 236.8Kbps (downlink) / 236.8Kbps (uplink)
supports Windows 7/8/10/11, Ubuntu, Raspberry Pi OS, OpenWRT...
Just plug it into USB port, go through some simple configuration, the high speed 4G network connection will be ready to use
for Windows PC or Jetson Nano series, use a USB cable
for Raspberry Pi 4B/3B+, or CM4-IO-BASE-A/B, use the purpose-made USB adapter
supported communication protocols: TCP, UDP, FTP, FTPS, HTTP, HTTPS...
supports GPS, Beidou, Glonass, Galileo, QZSS, and LBS base station positioning
allows using AT commands to make phone call or send SMS
compatible with Raspberry Pi series and Jetson Nano, stackable design for more HATs
better heat dissipation for both Raspberry Pi and the 4G module
Compatible with SIM7600X-M.2, SIM7906X-M.2, A7906X-M.2 series modules
- Raspberry Pi GPIO header
for connecting with Raspberry Pi - DIP switches
Enables the power control and reset pins - M.2 slot
Compatible with most SIMCom and QUECTEL 4G/5G modules in M.2 form factor - SIM card slot 1
one of the 2x SIM card slots, dual card single standby - USB3.1 port
USB 2.0 compatible, for connecting with different hosts - USB Type-C port
5V 3A input, stable and flexible power supply - Audio jack
SIM7600X/SIM8XXX series supports audio function, but RM5XX/EM06XX series temporarily does not support this function
- Antenna connector
Supports quad antennas - Reset button
- Power supply switch
Switch the power supply mode:
When set to USB, the module is powered via the "5. USB3.1 port"
When set to EXT PWR, the module is powered by the external power supply via the "6. USB Type-C port" - Cooling fan
Better heat dissipation for both Raspberry Pi and the 5G module - Indicator
Easy to monitor the operating status of module
- SIM card slot 2
Switchable via AT command - Module settings switch
Switch A to ON for SIM7600X/A7906X/SIM7906X/SIM7912X series 4G M.2 modules;
Switch B to ON for SIM8202X/SIM8200EA/SIM8262X series 5G M.2 modules;
Switch C to ON for RM50X/RM520N-GL/EM06X series 5G/LTE-A M.2 modules
- USB 2.0 interface pads
- NAU8810X Audio Chip
For SIM7600X/SIM8XXX series modules, RM5XX and EM06XX series modules temporarily does not support this function - Fan Header
5V cooling fan power supply
| SIM7600A-H | SIM7600SA-H | SIM7600E-H | SIM7600NA-H | SIM7600G-H | ||
|---|---|---|---|---|---|---|
| Form factor | M.2 | |||||
| Dimensions | 42.0 × 31.4 × 3.8 (mm) | |||||
| Freq. band |
LTE-FDD | B2, B4, B12 | B1, B2, B3, B4, B5, B7, B8, B28, B66 | B1, B3, B5, B7, B8, B20 | B2, B4, B5, B12, B13, B14, B25, B26, B66, B71 | B1, B2, B3, B4, B5, B7, B8, B12, B13, B18, B19, B20, B25, B26, B28, B66 |
| LTE-TDD | B40 | B38, B40, B41 | B41 | B34, B38, B39, B40, B41 | ||
| WCDMA | B2, B5 | B1, B2, B5, B8 | B1, B5, B8 | B1, B2, B4, B5, B6, B8, B19 | ||
| GSM | 850, 900, 1800, 1900MHz | 900, 1800MHz | 850, 900, 1800, 1900MHz | |||
| GNSS | GPS, Beidou, GLONASS, GALILEO, QZSS | |||||
| Applicable regions | North America (AT&T) | Australia, New Zealand, Taiwan, Latin America | Europe, the Middle East, Africa, South Korea, Thailand | North America (all providers) | Global | |
Weight: 0.215 kg
Quick Overview
- M.2 TO 4G/5G HAT x1
- SIM7600G-H-M.2 x1
- Antenna 2pcs x1
- IPEX adapter cable 2pcs x1
- 2*20PIN pin header x1
- Passive GPS antenna x1
- Dual plug USB3.0 cable x1
- USB3.0 adapter x1
- USB2.0 adapter x1
- SMA protective cap 2pcs x1
- Screws pack x1
