Details
For Evaluating The Raspberry Pi Compute Module Or Being Integrated Into End Products
Suitable for CM4S / CM3 series boards
Compute Module PoE Board
the base board only
CM4S08032 Package A
the base board + CM4S08032 (8GB RAM, 32GB eMMC Flash)
- Raspberry Pi GPIO header, for connecting sorts of Raspberry Pi HATs
- 10/100M auto-negotiation Ethernet port, with PoE enabled
- 4x USB ports, allows connecting more USB devices
- 2x CSI camera interfaces
- Onboard HDMI / DSI interfaces for connecting displays
- Onboard USB TO UART, for serial debugging
- Cooling fan interface, auto run on power up OR controlled by IO pins
- Adopts isolated SMPS (Switching Mode Power Supply)
| PoE power input | 37V ~ 57V DC in |
|---|---|
| PoE power output | 5V 2.5A DC out |
| Network standard | 802.3af PoE standard |
| Power supply | micro USB port / PoE Ethernet port |
| Mounting hole size | 3.2mm |
| Dimensions | 114mm × 84.4mm |
suitable for Raspberry Pi CM4S / CM3 / CM3L / CM3+ / CM3+L
Supports PoE Power supply, onboard multiple peripheral interfaces
Supports controlling the fan via GPIO or direct running from 5V power supply
* for reference only, the cooling fan and the case are NOT included.
Suitable For Raspberry Pi Applications Or Other Industrial Context Requiring Binocular Vision or PoE power supply
Base board interfaces
- Compute Module interface
for connecting Compute Module (CM4S / CM3 / CM3L / CM3+ / CM3+L) - Raspberry Pi GPIO header
for connecting Raspberry Pi HATs - PoE enabled Ethernet port
10/100M auto-negotiation, for connecting router or switch with PoE function - DSI interface
display port, for connecting Raspberry Pi LCD - USB ports
4x USB ports, for connecting USB devices - CSI interface
2x CSI camera ports, for connecting Raspberry Pi cameras - HDMI port
- USB TO UART interface
for serial debugging - USB SLAVE interface
allows you to burn system image into Compute Module - Power port
5V 2.5A - TF card slot (bottom side)
insert a TF card with pre-burnt system, to start up Compute Module 4S/3/3+ Lite variant - Cooling fan interface
Onboard components
- LAN9514 (bottom side)
fully-integrated USB hub and 10/100M Ethernet controller - Si3404 PoE power management chip (bottom side)
- CP2102 USB TO UART converter
- EP13 PoE power transformer
- Optical isolator
- Two LED indicators
Red: Raspberry Pi power indicator
Green: Raspberry Pi operating status indicator - NET network indicator
- Bridge rectifier
Jumper instruction
- VGx power config jumper: config the I/O level
- UART output config:
Left: connect the CP2102 serial port and Raspberry Pi serial port
Right: disconnect the CP2102 serial port and Raspberry Pi serial port - PoE config:
DIS: disable PoE
EN: enable PoE - Cooling fan config:
P34: the fan is program controlled via P34 pin
EN: the fan is directly powered from 5V power supply - PoE power voltage measuring pads
High speed eMMC, low power consumption
Based on the Raspberry Pi 4 Model B architecture, Compute Module 4S is intended for customers migrating or upgrading from Compute Module 3 / 3+
Upgraded processor BCM2711, quad-core Cortex-A72 64-bit Processor, more powerful performance. Onboard High-Speed eMMC Flash Memory Up to 100 MB/s, 4 times faster than CM3+
* Resources for different product may vary, please check the wiki page to confirm the actually provided resources.
Quick Overview
Compute Module PoE Board
Compute Module PoE Board x1
CM4S08032 Package A
- Compute Module PoE Board x1
- CM4S08032 x1
- USB cable ~35cm x2
- OPTIONS 5V 3A Power Supply x1
