MISC CAPE

From Waveshare Wiki
Jump to: navigation, search
MISC CAPE
Beaglebone MISC CAPE
MISC-CAPE l.jpg
{{{name2}}}
Beaglebone LCD CAPE (4.3inch)

{{{name3}}}

{{{name4}}}

{{{name5}}}

{{{name6}}}

Introduction

BB Black Expansion CAPE, Features Miscellaneous Components and Functions

More

Getting Ready

Writing the TF Card System Image

Follow the steps below to write the Angstrom into TF card:

1) Extract the system image

Extract the system image file .img.7z by using archiver software like 7z920.exe.

Note: please download the image file from:

LCD CPAE(4.3inch) image for testing

LCD CPAE(7inch) image for testing

MISC CAPE and RS485/CAN CAPE image for testing

2) Format the TF card

Use HPUSBDisk.exe to format the TF card.

Choose the Device as your TF card, File system as FAT32. Then click Start.

Note: the TF card capacity should be 4GB or above!


Use HPUSBDisk.exe to format the TF card
XXX-CAPE-User-Manual-001.jpg

3) Writing the system image

Launch Win32DiskImager.exe, select the extracted system image. Then click write.


Use Win32DiskImager.exe to write the system image
XXX-CAPE-User-Manual-002.png

Install USB to UART driver

1) Connect the LCD CAPE with USB TO UART interface to the PC through a USB cable.

Note: You need to install the corresponding driver. Please refer to the respective manuals of your USB TO UART module.

Interface definition:

  • Red: VCC
  • Black: GND
  • Green: TXD(connect to RXD)
  • White: RXD(connect to TXD)
USB to UART Cable
XXX-CAPE-User-Manual-003.jpg

2) Open PL2303_Prolific_DriverInstaller_v1.8.0.exe and install the driver.

3) Launch putty.exe, configure as follows, then click Open.


PuTTY Settings
XXX-CAPE-User-Manual-004.jpg

Note:

  • Serial line: check the PC "Device Manager" to confirm which COM port should be selected.
  • Speed: 115200
  • Connection type: Serial

Enter Bash Shell

1) Insert the TF card into the BeagleBone Black onboard slot, keep pressing down the BOOT button, power up the board, then release the BOOT button.

2) When the system startups, input "root" to enter Bash Shell environment, now the shell commands are available to use. All the commands follows are executed here.

Enter Bash Shell
XXX-CAPE-User-Manual-005.jpg

Note: please make sure that you are using the TF card image that we provide, and the system should boot from TF card (keep pressing down BOOT button, then power up), otherwise, the testing will fail.

API Source Code

The API source code can be found on /home/xuser/waveshare_demo/API.

LCD CAPE

LCD Display Overview

XXX-CAPE-User-Manual-006.jpg

  1. BB_BLACK connector : for connecting BB Black
  2. 4.3inch LCD interface : for connecting 4.3inch resistive touchscreen LCD
  3. DEBUG interface : BB Black debug interface, for connecting serial modules
  4. BOOT selection button: Boot from TF card

XXX-CAPE-User-Manual-007.jpg

  1. BB_BLACK connector : for connecting BB Black
  2. 7inch LCD interface : for connecting 7inch resistive touchscreen LCD
  3. DEBUG interface : BB Black debug interface, for connecting serial modules
  4. BOOT selection button : Boot from TF card

LCD Display

1) Connect to a LCD

Note: There are two models of LCD CAPE, LCD CAPE (4.3inch) and LCD CAPE (7inch), each one corresponds our 4.3inch or 7inch resistive touch screen respectively. Some batches of LCD CAPE provide both interfaces. If the CAPE connected to the LCD by a wrong interface, it may damage the LCD and the main board.

  • When using 4.3inch LCD

Download LCD CPAE(4.3inch) image for testing.

Connect BB Black to the 4.3inch LCD.


Connect to the 4.3inch LCD
XXX-CAPE-User-Manual-008.jpg
  • When using 7inch LCD

Download LCD CPAE(7inch) image for testing.

Connect BB Black to the 7inch LCD.

Connect to the 7inch LCD
XXX-CAPE-User-Manual-009.jpg

2) The touchscreen should be calibrated when the display mode has been changed: 

root@beaglebone:~# rm -rf /etc/pointercal*
root@beaglebone:~# ts_calibrate
root@beaglebone:~# sync

Reboot the system. Note: if the calibration failed, reboot and retry again.

MISC CAPE

MISC CAPE Overview

XXX-CAPE-User-Manual-010.jpg
  1. BB_BLACK connector : for connecting BB Black
  2. DEBUG interface : BB Black debug interface, for connecting serial modules
  3. ONE-WIRE interface: easily connects to ONE-WIRE devices (TO-92 package), such as temperature sensor (DS18B20), electronic registration number (DS2401), etc.
  4. BOOT selection button : Boot from TF card
  5. User button : 4 buttons
  6. Buzzer
  7. Power indicator
  8. User LED : 4 LEDs
  9. Potentiometer : AD adjustable potentiometer
  10. 32.768KHz crystal : for RTC
  11. PCF8563 : RTC
  12. RTC battery holder : for 3.3V battery
  13. RTC power selection jumper
  14. RTC I2C selection jumper: select I2C1 OR I2C2

LED

Short the LED jumper, enter: 

root@beaglebone:~# test_led

The 4 LEDs will light up one by one, press Ctrl+C to exit.

Buzzer

1) Short the buzzer jumper, enter: 

root@beaglebone:~# ls /sys/devices/ocp.3/

You'll find the “pwm_ehrpwm1b.14” as shown:

Find the “pwm_ehrpwm1b.14”
XXX-CAPE-User-Manual-011.jpg

2) Because the pwm_ehrpwm1b.14's extension is .14. It is needed to add parameter 14 when buzzer tested. 

root@beaglebone:~# test_pwm 14

The buzzer will make sounds in different frequency.

DS18B20

1) Insert the DS18B20 into the 1-WIRE socket, short the 1-WIRE jumper, enter: 

root@beaglebone:~#ls /sys/bus/w1/devices/

You will find the "28-00000 57c5948" (the last 7 characters are unique for each DS18B20, it depends)

2) Execute: 

root@beaglebone:~#test_ds18b20  57c5948

The terminal will print the current temperature.

Buttons

1) Execute 

root@beaglebone:~# test_key event2

Note: Device file "event2" is based on user‘s device, Not necessarily "event2". you can execute the following command to view: 

root@beaglebone:~# ls /dev/input
Check event device
XXX-CAPE-User-Manual-012.jpg

2) Press any of the onboard buttons, the terminal will show which one has been pressed, press Ctrl+C to exit.

Note: if the LCD screen was connected while testing joystick/buttons, the LCD screen seems that it was touched at the same time, it's normal.

RTC

Confirm that the module is powered by onboard battery.

1) Show system date time: 

root@beaglebone:~# date

2) Set system date time: 

root@beaglebone:~# date 020809302014.23

3) Set the hardware clock of RTC module: 

root@beaglebone:~# hwclock –w –f /dev/rtc1

4) Show the hardware clock of RTC module: 

root@beaglebone:~# hwclock –r –f /dev/rtc1

5) Synchronize the hardware clock to system date time: 

root@beaglebone:~# hwclock –s –f /dev/rtc1


Synchronize the hardware clock to system date time
XXX-CAPE-User-Manual-013.jpg

6) Power off and reboot, read the hardware clock of RTC module and synchronize to system date time: 

root@beaglebone:~# hwclock –r –f /dev/rtc1

root@beaglebone:~# hwclock –s –f /dev/rtc1

root@beaglebone:~# date
Synchronize to system date time
XXX-CAPE-User-Manual-014.jpg

Now the date time of software and hardware are synchronous.

RS485 CAN CAPE

CAN

Two BeagleBone Black and two RS485/CAN CAPEs are required for this testing. Set jumper to enable UART1(RXD1, TXD1). Connect two CAN Board to CAN1 interface separately, connect the CANH, CANL of one module to the CANH, CANL of another module via jumper wires.

1) Configure the baud rate: 

root@beaglebone:~#canconfig can0 bitrate 115200 ctrlmode triple-sampling on

2) Enable the CAN device: 

root@beaglebone:~# canconfig can0 start

The two CAN devices act as receiver and sender separately. The receiver gets ready to receive data first, and then the sender starts sending data.

3) Receiver: 

root@beaglebone:~# candump can0

As shown in the picture:

CAN receiver status
XXX-CAPE-User-Manual-015.jpg

4) Sender: 

root@beaglebone:~# cansend can0 -i 0x11 0x12 0x13 0x14

As shown in the picture:

CAN wender status
XXX-CAPE-User-Manual-016.jpg

5) Stop the devices: 

root@beaglebone:~# canconfig can0 stop

RS485

Two BeagleBone Black and two RS485/CAN CAPEs are required for this testing. Set jumper to enable UART2(RXD2, TXD2). Connect two RS485 Boards to UART2 interface separately. Connect the A, B of one module to the A, B of another module via jumper wires.

The two RS485 devices act as receiver and sender separately.

1) The receiver gets ready to receive data first, and then the sender starts sending data. Execute: 

root@beaglebone:~# test_485 –d /dev/ttyO2 –b 115200

2) Receiver:

Select "2", it will keep receiving data until you select "3".

As shown in the picture:

RS485 receiver status
XXX-CAPE-User-Manual-017.jpg

3) Sender:

Select "1", and then enter the message, say, "abc", it loops sending the message until you select "3".

As shown in the picture:

RS485 sender status
XXX-CAPE-User-Manual-018.jpg

4) Press Ctrl+C to exit.

Other Expansion Module

USB Camera

1) Connect the USB Camera to the BeagleBone Black USB Host connector.

2) Check the assigned IP: 

root@beaglebone:~# ifconfig eth0
Check the assigned IP
XXX-CAPE-User-Manual-019.jpg

As shown in the picture, the IP is 192.168.1.143. Note this IP(it depends).

3) Start up the video stream server: 

root@beaglebone:~# cd/home/xuser/waveshare_demo/API/camera_test/mjpg-streamer

root@beaglebone:~# ./ start.sh
Start up the video stream server
XXX-CAPE-User-Manual-020.jpg

4) Open browser on the PC in the same local network, visit the following address to view the video (default port number is 8080):

http://192.168.1.143:8080/javascript.html

(It depends on the IP you have noted)

Visit video stream server
XXX-CAPE-User-Manual-021.jpg

5) Press Ctrl+C to exit.

USB WIFI

1) Config the wireless network:

a) Power off, connect the USB WIFI module to the BeagleBone Black USB Host connector, and power up again.

b) Check the USB status: 

root@beaglebone:~# lsusb
Check the USB status:
XXX-CAPE-User-Manual-022.jpg

c) Check the network status: 

root@beaglebone:~# ifconfig
Check the network status
XXX-CAPE-User-Manual-023.jpg

d) Shut down the Ethernet NIC, and start up the WIFI NIC: 

root@beaglebone:~# ifconfig eth0 down

root@beaglebone:~# ifconfig wlan0 up

e)Check the WIFI status: 

root@beaglebone:~# ifconfig
Check the WIFI status:
XXX-CAPE-User-Manual-024.jpg

There's no AP connected, therefore, the wlan0 RX TX packets are both 0.

f) Config the wlan0 IP: 

root@beaglebone:~# ifconfig wlan0 192.168.2.107

g) Config the gateway: 

root@beaglebone:~# route add default gw 192.168.2.1

h) Config the DNS: 

root@beaglebone:~# vi /etc/resolv.conf

Edit

nameserver 127.0.0.1

As:

nameserver 8.8.8.8

Configure the DNS.
XXX-CAPE-User-Manual-025.jpg

Save and exit.

i) Scan wireless router: 

root@beaglebone:~# iwlist wlan0 scan
Scan wireless router
XXX-CAPE-User-Manual-026.jpg

2) Connect to the router:

a) Config the key file /etc/wpa_supplicant.conf: 

root@beaglebone:~# vi /etc/wpa_supplicant.conf

Edit: 

network={

    key_mgmt=NONE

}

As: 

network={ 

    ssid="waveshare" 

    psk="12345678"

}

Save and exit.

b) Connect manually: 

root@beaglebone:~# wpa_supplicant -B -i wlan0 -c /etc/wpa_supplicant.conf

c) Test the connection: 

root@beaglebone:~# ping www.baidu.com
Test WIFI connection:
XXX-CAPE-User-Manual-027.jpg

Resource

Documentations

Tools

PL2303_Prolific_DriverInstaller_v1.8.0
Win32DiskImager
7z920.exe
HPUSBDisk
putty

Cross-compilation toolchain

arm-2010.09-50-arm-none-linux-gnueabi-i686-pc-linux-gnu.tar

Source Code

driver
dts
tslib
wifi
mjpg-streamer

Kernel

Kernel_config

FAQ

Question:It didn't come with a battery, why?

 Answer:
Due to shipping reasons, this product doesn't come with any batteries. You shall place a CR1220 button battery into the socket for clocking usage.
{{{3}}}
{{{4}}}

{{{5}}}





Technical Support

If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. Please be patient as we make every effort to help you to resolve the issue.
Working Time: 9 AM - 6 PM GMT+8 (Monday to Friday)

Retrieved from "https://www.waveshare.com/w/index.php?title=MISC_CAPE&oldid=70176"