Without case

ESP32-S3-Touch-AMOLED-1.43-introduction-02.png

ESP32-S3, Type-C USB

With metal case

ESP32-S3-Touch-AMOLED-1.43-introduction-01.png

ESP32-S3, Type-C USB

Overview

Introduction

ESP32-S3-Touch-AMOLED-1.43 is a low-cost, high-performance and highly scalable ESP32_GUI development board designed by Waveshare. It supports 2.4GHz WiFi and BLE 5, integrated high-capacity Flash and PSRAM, onboard RTC, IMU and 1.43-inch AMOLED screen, exposed UART, GPIO, I2C and USB bus interfaces, and a large number of demos and technical support for you to quickly develop automation and IoT products.

Features

Equipped with high-performance Xtensa 32-bit LX7 dual-core processor, up to 240MHz main frequency
Supports 2.4GHz Wi-Fi (802.11 b/g/n) and Bluetooth 5 (BLE), with onboard antenna
Built-in 512KB SRAM and 384KB ROM, with onboard 16MB Flash and 8MB PSRAM
Onboard 1.43inch wide capacitive touch screen with 466 × 466 resolution, 16.7M color
AMOLED screen display uses a QSPI interface, touch screen uses an I2C interface, capacitive touch control, supports interrupt output
Onboard RTC, IMU, TF card slot; leads out the I2C and UART buses, while exposing USB_N and USB_P; makes it suitable for various occasions

Onboard Resources

1. ESP32-S3R8

2. 16MB Flash

3. QMI8658
IMU attitude chip

4. PCF85063
RTC clock chip

5. 3.7V Lithium battery interface

6. TF card slot (back)

7. RTC independent power interface

8. I2C interface

9. Charge indicator

10. Type-C interface

11. Power indicator

12. UART interface

13. BOOT button

14. RESET button

15. IPEX1 external antenna interface (resoldering required)

16. Ceramic antenna (default)

Interfaces

For more details, please refer to the Schematic diagram

ESP32-Touch-AMOLED-1.43	AMOLED	SD_Card	IMU	RTC	UART	I2C	KEY_IO	GPIO
GPIO0							BOOT0	GPIO0
GPIO1								GPIO1
GPIO2								GPIO2
GPIO3								GPIO3
GPIO4								BAT_ADC
GPIO5								GPIO5
GPIO6								GPIO6
GPIO7								GPIO7
GPIO8			IMU_INT
GPIO9	QSPI_CS
GPIO10	QSPI_CLK
GPIO11	QSPI_D0
GPIO12	QSPI_D1
GPIO13	QSPI_D2
GPIO14	QSPI_D3
GPIO15				RTC_INT
GPIO16								GPIO16
GPIO17								GPIO17
GPIO18								GPIO18
GPIO19								USB_N
GPIO20								USB_P
GPIO21	AMOLED_RST
GPIO38		SD_CS						GPIO38
GPIO39		SD_MOSI						GPIO39
GPIO40		SD_MISO						GPIO40
GPIO41		SD_SCLK						GPIO41
GPIO42	AMOLED_EN
GPIO43					UART_TXD			TXD
GPIO44					UART_RXD			RXD
GPIO45								GPIO45
GPIO46								GPIO46
GPIO47	TP_SDA		IMU_SDA	RTC_SDA		SDA		SDA
GPIO48	TP_SCL		IMU_SCL	RTC_SCL		SCL		SCL
EN							RESET

Dimensions

Without case version

With case version

AMOLED Specifications

Usage Instructions

ESP32-S3-Touch-AMOLED-1.43 currently provides two development tools and frameworks, Arduino IDE and ESP-IDF, providing flexible development options, you can choose the right development tool according to your project needs and personal habits.

Development Tools

Arduino IDE

Arduino IDE is an open source electronic prototyping platform, convenient and flexible, easy to get started. After a simple learning, you can start to develop quickly. At the same time, Arduino has a large global user community, providing an abundance of open source code, project examples and tutorials, as well as rich library resources, encapsulating complex functions, allowing developers to quickly implement various functions.

ESP-IDF

ESP-IDF, or full name Espressif IDE, is a professional development framework introduced by Espressif Technology for the ESP series chips. It is developed using the C language, including a compiler, debugger, and flashing tool, etc., and can be developed via the command lines or through an integrated development environment (such as Visual Studio Code with the Espressif IDF plugin). The plugin offers features such as code navigation, project management, and debugging, etc..

Each of these two development approaches has its own advantages, and developers can choose according to their needs and skill levels. Arduino are suitable for beginners and non-professionals because they are easy to learn and quick to get started. ESP-IDF is a better choice for developers with a professional background or high performance requirements, as it provides more advanced development tools and greater control capabilities for the development of complex projects.

Components Preparation

ESP32-S3-Touch-AMOLED-1.43 x1
TF card (capacity less than 64G) x1
USB cable (Type-A to Type-C) x 1

Before operating, it is recommended to browse the table of contents to quickly understand the document structure. For smooth operation, please read the FAQ carefully to understand possible problems in advance. All resources in the document are provided with hyperlinks for easy download.

Working with Arduino

This chapter introduces setting up the Arduino environment, including the Arduino IDE, management of ESP32 boards, installation of related libraries, program compilation and downloading, as well as testing demos. It aims to help users master the development board and facilitate secondary development.

Environment Setup

Download and Install Arduino IDE

Click to visit the Arduino official website, select the corresponding system and system bit to download
Run the installer and install all by default

The environment setup is carried out on the Windows 10 system, Linux and Mac users can access Arduino-esp32 environment setup for reference

Install ESP32 Development Board

Before using ESP32-related motherboards with the Arduino IDE, you must first install the software package for the esp32 by Espressif Systems development board
According to Board installation requirement, it is generally recommended to use Install Online. If online installation fails, use Install Offline.
For the installation tutorial, please refer to Arduino board manager tutorial

ESP32-S3-Touch-AMOLED-1.43 required development board installation description
Board name	Board installation requirement	Version number requirement
esp32 by Espressif Systems	"Install Offline" / "Install Online"	≥3.1.0

Install Library

When installing Arduino libraries, there are usually two ways to choose from: Install online and Install offline. If the library installation requires offline installation, you must use the provided library file
For most libraries, users can easily search and install them through the online library manager of the Arduino software. However, some open-source libraries or custom libraries are not synchronized to the Arduino Library Manager, so they cannot be acquired through online searches. In this case, users can only manually install these libraries offline.
For library installation tutorial, please refer to Arduino library manager tutorial

ESP32-S3-Touch-AMOLED-1.43 library file path:

..\ESP32-S3-Touch-AMOLED-1.43-Demo\Arduino\libraries

ESP32-S3-Touch-AMOLED-1.43 library file installation instructions
Library Name	Description	Version	Library Installation Requirement
LVGL	Graphical library	v8.4.0	"Install Offline"

Run the First Arduino Demo

If you are just getting started with ESP32 and Arduino, and you don't know how to create, compile, flash, and run Arduino ESP32 programs, then please expand and take a look. Hope it can help you!

New Project

Run the Arduino IDE and select File -> New Sketch
Enter the code:

void setup() {
  // put your setup code here, to run once:
  Serial.begin(115200);
}

void loop() {
  // put your main code here, to run repeatedly:
  Serial.println("Hello, World!");
  delay(2000);
}

Save the project and select File -> Save As.... In the pop-up menu, select the path to save the project, and enter a project name, such as Hello_World, click Save

Compile and Flash Demos

Select the corresponding development board, take the ESP32S3 motherboard as an example:

①. Click to select the dropdown menu option Select Other Board and Port;
②. Search for the required development board model esp32s3 dev module and select;
③. Select COM Port;
④. Save the selection.

Some development boards with specified version numbers support direct model selection, for example, "Waveshare ESP32-S3-LCD-1.69":

If the ESP32S3 mainboard only has a USB port, you need to enable USB CDC, as shown in the following diagram:

Compile and upload the program:

①. Compile the program; ②. Compile and download the program; ③. Download successful.

Open the Serial Monitor window, and the demo will print "Hello World!" every 2 seconds, and the operation is as follows:

Demo

ESP32-S3-Touch-AMOLED-1.43 Demo
Demo	Basic Description	Dependency Library
01_ADC_Test	Read the current voltage value of the system	-
02_I2C_PCF85063	Print the real-time time of RTC chip	-
03_I2C_QMI8658	Print the original data sent by the IMU	-
04_SD_Card	Load and display the information of the TF card	-
05_WIFI_AP	Set to AP mode to obtain the IP address of the access device	-
06_WIFI_STA	Set to STA mode to connect to WiFi and obtain an IP address	-
07_LVGL_Test	LVGL demo	LVGL

Arduino Project Parameter Setting

01_ADC_Test

Demo description

The analog voltage connected through the GPIO is converted to digital by the ADC, and then the actual system voltage is calculated and printed to the terminal

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

adc_bsp_init(void) : Initializes ADC1, including creating an ADC one-time trigger unit and configuring channel 3 for ADC1
adc_get_value(float *value,int *data) : Reads the value of ADC1 channel 3 and calculates the corresponding voltage value based on the reference voltage and resolution, stores it at the position where the incoming pointer points to, and stores 0 if the read fails
adc_example(void* parameter): Initialize ADC1 and then create an ADC task that reads the ADC value every 1 second and calculates the system's voltage based on the raw ADC value

Result demonstration

The program compilation download is complete, and opening the serial port monitor will show the printed ADC values and voltage, as shown in the following figure:

The ADC sampling value is about 1900, and the system voltage is about 4.9V. For a detailed analysis, you can refer to the schematic diagram

02_I2C_PCF85063

Demo description

Through the I2C protocol, initialize the PCF85063 chip, set the time, and then periodically read the time and print it to the terminal

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

void PCF85063_example(void* parameter) : Create an RTC task to implement RTC functionality, reading the clock from the RTC chip every 10 seconds and then outputting it to the terminal

Result demonstration

Open the serial port monitoring, you can see the RTC time of the printout, as shown in the figure below:

Data is output every 10 seconds. If you need to modify or refer to it, you can directly access the PCF85063 source file for operations.

03_I2C_QMI8658

Demo description

Through I2C protocol, initialize the QMI8658 chip, then read and print the corresponding attitude information every 1 second to the terminal

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

qmi8658c_example(void* parameter): The function initializes the QMI8658 device, reading and printing accelerometer data, gyroscope data, and temperature data in an infinite loop, once every second. During the rotation of the board, the gyroscope data increases with greater rotation speed, and the accelerometer calculates the corresponding acceleration based on the current position.

Result demonstration

Open the serial port monitoring, and you can see the original data output from the IMU (Euler angles need to be converted by yourself), as shown in the following figure:

Data is output once every second. If you need to modify or refer to it, you can directly access the qmi source file for operations

04_SD_Card

Demo description

Select SPI or SDMMC direction to drive the TF card through macro definition, and print the TF card information to the terminal after successfully mounting the TF card

Hardware connection

Install a TF card on the board (you must insert a TF card with a capacity of less than 64G first), and use a USB cable to connect the board to the computer

Code analysis

The communication protocol of the TF card can be implemented according to the user's choice, find the macro definition SD_Read_Mode under the source file sd_card_bsp.cpp, the macro definition uses the SDMMC communication protocol by default, which can be modified to SDSPI

#define SD_Read_Mode USER_SPI

Result demonstration

Click on the serial port monitoring device, you can see the information of the output TF card, practical_size is the actual capacity of the TF card, as shown in the figure below:

How to know more about the Arduino ESP32 libraries which explain the use of TF card? Please refer to Arduino ESP32 library TF card use

05_WIFI_AP

Demo description

Use the development board as an AP waiting for STA terminal connection

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

The code initializes serial communication on the ESP32 and then creates a WiFi access point named "bsp_esp_demo" with the password "waveshare", and no other continuous operations are performed in a loop while the program runs.

const char* ssid     = "bsp_esp_demo";
const char* password = "waveshare"; 

WiFi.softAP(ssid,password);

Result demonstration

Use your mobile phone or other device to connect to WIFI, the WiFi name is "bsp_esp_demo", and the password is "waveshare"

06_WIFI_STA

Demo description

The development board is used as a terminal role, which can connect to the AP available in the environment, and print the obtained IP information to the terminal after successful connection

Hardware connection

Connect the board to the computer using a USB cable

Code modification

This project implements the chip connecting to WIFI and obtaining an IP address while in STA mode. Before compiling and downloading the firmware, some code needs to be modified to the name and password of the available WIFI router in the current environment

Code analysis

wifi_init(void): This function is used to initialize the Wi-Fi connection of the ESP32. It sets the ESP32 to Wi-Fi site mode and tries to connect to the specified Wi-Fi network (via the ssid and password). If the connection is successful, it prints the local IP address; if the connection fails within a certain period (20 * 500 milliseconds), it prints the connection failure message. At the same time, the function can also set the auto-connection and auto-reconnect functions

Result demonstration

The chip is successfully connected to WIFI in STA mode, and you can see the obtained IP address by clicking on the serial port monitoring device

07_LVGL_Test

Demo description

Implement some multifunctional GUI interfaces on the screen by porting LVGL

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

For LVGL, lvgl_conf.h is its configuration file. Below, some commonly used settings are explained, and some LVGL demos and file systems can also be configured in the conf file

/*Color depth: 1 (1 byte per pixel), 8 (RGB332), 16 (RGB565), 32 (ARGB8888)*/
#define LV_COLOR_DEPTH 16//Color depth, a macro definition that must be concerned with porting LVGL


#define LV_MEM_CUSTOM 0
#if LV_MEM_CUSTOM == 0
    /*Size of the memory available for `lv_mem_alloc()` in bytes (>= 2kB)*/
    #define LV_MEM_SIZE (48U * 1024U)          /*[bytes]*/

    /*Set an address for the memory pool instead of allocating it as a normal array. Can be in external SRAM too.*/
    #define LV_MEM_ADR 0     /*0: unused*/
    /*Instead of an address give a memory allocator that will be called to get a memory pool for LVGL. E.g. my_malloc*/
    #if LV_MEM_ADR == 0
        #undef LV_MEM_POOL_INCLUDE
        #undef LV_MEM_POOL_ALLOC
    #endif

#else       /*LV_MEM_CUSTOM*/
    #define LV_MEM_CUSTOM_INCLUDE <stdlib.h>   /*Header for the dynamic memory function*/
    #define LV_MEM_CUSTOM_ALLOC   malloc
    #define LV_MEM_CUSTOM_FREE    free
    #define LV_MEM_CUSTOM_REALLOC realloc
#endif     /*LV_MEM_CUSTOM*/
//The above section is mainly for LVGL memory allocation, 
//which defaults to lv_mem_alloc() versus lv_mem_free().

Code modification

The display chip itself does not support hardware rotation. If rotation is needed, it can be achieved through software. You can find the macro definition #define EXAMPLE_Rotate_90 in lcd_bsp.c file and uncomment this macro definition. Software rotation performance is not as good as hardware rotation

#define EXAMPLE_Rotate_90

Result demonstration

The LVGL demo has high requirements for RAM and ROM, so it is necessary to configure the demo according to the requirements of environment setup, and after the program is flashed, the running effect of the device is as follows:

For more learning and use of LVGL, please refer to LVGL official documentation

Working with ESP-IDF

This chapter introduces setting up the ESP-IDF environment setup, including the installation of Visual Studio and the Espressif IDF plugin, program compilation, downloading, and testing of demos, to assist users in mastering the development board and facilitating secondary development.

Environment Setup

Download and Install Visual Studio

Open the download page of VScode official website, choose the corresponding system and system bit to download
After running the installation package, the rest can be installed by default, but here for the subsequent experience, it is recommended to check boxes 1, 2, and 3
- After the first two items are enabled, you can open VSCode directly by right-clicking files or directories, which can improve the subsequent user experience.
- After the third item is enabled, you can select VSCode directly when you choose how to open it.

The environment setup is carried out on the Windows 10 system, Linux and Mac users can access ESP-IDF environment setup for reference

Install Espressif IDF Plugin

It is generally recommended to use Install Online. If online installation fails due to network factor, use Install OIffline.
For more information about how to install the Espressif IDF plugin, see Install Espressif IDF Plugin

Run the First ESP-IDF Demo

If you are just getting started with ESP32 and ESP-IDF, and you don't know how to create, compile, flash, and run ESP-IDF ESP32 programs, then please expand and take a look. Hope it can help you!

New Project

Create Demo

Using the shortcut F1, enter esp-idf:show examples projects

Select your current IDF version

Take the Hello world demo as an example

①Select the corresponding demo
②Its readme will state what chip the demo applies to (how to use the demo and the file structure are described below, omitted here)
③Click to create the demo

Select the path to save the demo, and require that the demos cannot use folders with the same name

Modify COM Port

The corresponding COM ports are shown here, click to modify them
Please select the COM ports according to your device (You can view it from the device manager)
In case of a download failure, please press the Reset button for more than 1 second or enter download mode, and wait for the PC to recognize the device again before downloading once more

Modify Driver Object

Select the object we need to drive, which is our main chip ESP32S3

Choose the path to openocd, it doesn't affect us here, so let's just choose one

Introduction to Other Status Bar Functions

①.ESP-IDF Development Environment Version Manager, when our project requires differentiation of development environment versions, it can be managed by installing different versions of ESP-IDF. When the project uses a specific version, it can be switched to by utilizing it
②.Device flashing COM port, select to flash the compiled program into the chip
③.Select set-target chip model, select the corresponding chip model, for example, ESP32-P4-NANO needs to choose esp32p4 as the target chip
④.menuconfig, click it to Modify sdkconfig configuration file Project configuration details
⑤.fullclean button, when the project compilation error or other operations pollute the compiled content, you can clean up all the compiled content by clicking it
⑥.Build project, when a project satisfies the build, click this button to compile
⑦.Current download mode, the default is UART
⑧.flash button, when a project build is completed, select the COM port of the corresponding development board, and click this button to flash the compiled firmware to the chip
⑨.monitor enable flashing port monitoring, when a project passes through Build --> Flash, click this button to view the log of output from flashing port and debugging port, so as to observe whether the application works normally
⑩.Debug
⑪.Build Flash Monitor one-click button, which is used to continuously execute Build --> Flash --> Monitor, often referred to as "little flame"

Compile, Flash and Serial Port Monitor

Click on the all-in-one button we described before to compile, flash and open the serial port monitor

It may take a long time to compile especially for the first time

During this process, the ESP-IDF may take up a lot of CPU resources, so it may cause the system to lag
If it is the first time to flash the program for a new project, you will need to select the download method, and select UART

This can also be changed later in the Download methods section (click on it to pop up the options)

As it comes with the onboard automatic download circuit, it can be downloaded automatically without manual operation
After successful download, it will automatically enter the serial monitor, you can see the chip output the corresponding information and be prompted to restart after 10S

Use the IDF Demos

The following takes ESP32-S3-LCD-1.47-Demo as an example to introduce the two opening methods of the project and the general steps of use, and the detailed explanation of the ESP-IDF project. If you use other projects, the operation steps can be applied similarly.

Open in the software

Open VScode software and select the folder to open the demo

Select the provided ESP-IDF example and click to select the file (located in the Examples/Demo/ESP-IDF path)

Open from Outside the Software

Select the project directory correctly and open the project, otherwise it will affect the compilation and flashing of subsequent programs

After connecting the device, select the COM port and model, click below to compile and flash to achieve program control

ESP-IDF Project Details

Component: The components in ESP-IDF are the basic modules for building applications, each component is usually a relatively independent code base or library, which can implement specific functions or services, and can be reused by applications or other components, similar to the definition of libraries in Python development.
- Component reference: The import of libraries in the Python development environment only requires to "import library name or path", while ESP-IDF is based on the C language, and the importing of libraries is configured and defined through CMakeLists.txt.
- The purpose of CmakeLists.txt: When compiling ESP-IDF, the build tool CMake first reads the content of the top-level CMakeLists.txt in the project directory to read the build rules and identify the content to be compiled. When the required components and demos are imported into the CMakeLists.txt, the compilation tool CMake will import each content that needs to be compiled according to the index. The compilation process is as follows:

Demo

ESP32-S3-Touch-AMOLED-1.43 Demo
Demo	Basic Description	Dependency Library
01_ADC_Test	Read the current voltage value of the system	-
02_I2C_PCF85063	Print the real-time time of RTC chip	-
03_I2C_QMI8658	Print the original data sent by the IMU	-
04_SD_Card	Load and display the information of the TF card	-
05_WIFI_AP	Set to AP mode to obtain the IP address of the access device	-
06_WIFI_STA	Set to STA mode to connect to WiFi and obtain an IP address	-
07_LVGL_Test	LVGL demo	LVGL
08_LVGL_SDIMG	Combine LVGL & SDCard & IMG demos	LVGL
09_FactoryProgram	Comprehensive project	LVGL

01_ADC_Test

Demo description

The analog voltage connected through the GPIO is converted to digital by the ADC, and then the actual system voltage is calculated and printed to the terminal

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

adc_bsp_init(void) : Initializes ADC1, including creating an ADC one-time trigger unit and configuring channel 3 for ADC1
adc_get_value(float *value,int *data) : Reads the value of ADC1 channel 3 and calculates the corresponding voltage value based on the reference voltage and resolution, stores it at the position where the incoming pointer points to, and stores 0 if the read fails
adc_example(void* parameter): Initialize ADC1 and then create an ADC task that reads the ADC value every 1 second and calculates the system's voltage based on the raw ADC value

Result demonstration

After the program is flashed, open the monitoring device and you can see the output ADC values and voltage, as shown in the figure below:

The ADC sampling value is about 1960, and the system voltage is about 4.92V. For a detailed analysis, you can refer to the schematic diagram

02_I2C_PCF85063

Demo description

Through the I2C protocol, initialize the PCF85063 chip, set the time, and then periodically read the time and print it to the terminal

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

void PCF85063_example(void* parameter) : Create an RTC task to implement RTC functionality, read the clock from the RTC chip every 10 seconds and then output it to the terminal

Result demonstration

After burning is completed, open the monitoring device to see the printed RTC time, as shown in the following figure:

Data is output every 10 seconds. If you need to modify or refer to it, you can directly access the PCF85063 source file for operations.

03_I2C_QMI8658

Demo description

Through I2C protocol, initialize the QMI8658 chip, then read and print the corresponding attitude information every 1 second to the terminal

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

qmi8658c_example(void* parameter): The function initializes the QMI8658 device, reading and printing accelerometer data, gyroscope data, and temperature data in an infinite loop, once every second. During the rotation of the board, the gyroscope data increases with greater rotation speed, and the accelerometer calculates the corresponding acceleration based on the current position.

Result demonstration

After the demo is flashed, the running result of the device is as follows:

Open the serial port monitoring, and you can see the original data output from the IMU (Euler angles need to be converted by yourself), as shown in the following figure:

You can see that it is output every 1 second. If you need to modify or refer to it, you can directly go to the qmi source file to modify it

04_SD_Card

Hardware connection

Install a TF card on the board (you must insert a TF card with a capacity of less than 64G first), and use a USB cable to connect the board to the computer

Demo description

Select SPI or SDMMC direction to drive the TF card through macro definition, and print the TF card information to the terminal after successfully mounting the TF card

Code analysis

The communication protocol of the TF card can be implemented according to the user's choice, find the macro definition SD_Read_Mode under the source file sd_card_bsp.cpp, the macro definition uses the SDMMC communication protocol by default, which can be modified to SDSPI

#define SD_Read_Mode USER_SPI

Result demonstration

Click on the serial port monitoring device, you can see the information of the output TF card, practical_size is the actual capacity of the TF card, as shown in the figure below:

How to know more about the Arduino ESP32 libraries which explain the use of TF card? Please refer to Arduino ESP32 library TF card use.

05_WIFI_AP

Demo description

Use the development board as an AP waiting for STA terminal connection

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

wifi_init_softap(void): This function is used to initialize the ESP32's Wi-Fi soft access point, including setting up the network interface, registering event handling functions, configuring soft AP parameters, and starting the soft AP

Result demonstration

When the chip is in AP mode, use the mobile phone to successfully connect to WIFI and the serial port will print the MACA address of the connected device and the IP address assigned to the device

06_WIFI_STA

Demo description

The development board is used as a terminal role, which can connect to the AP available in the environment, and print the obtained IP information to the terminal after successful connection

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

espwifi_Init(void): This function is used for WiFi initialization on ESP32. It sequentially initializes non-volatile storage, the TCP/IP stack, creates a default event loop and a default WiFi site network interface, initializes WiFi with the default configuration, registers event handlers to handle WiFi and IP-related events, sets WiFi connection parameters, and starts WiFi.

Code modification

This project implements the chip connecting to WIFI and obtaining an IP address while in STA mode. Before compiling and downloading the firmware, some code needs to be modified to the name and password of the available WIFI router in the current environment

Result demonstration

After the demo is flashed, the running result of the device is as follows:

The chip successfully connects to WIFI and obtains an IP address while in STA mode

07_LVGL_Test

Demo description

Implement some multifunctional GUI interfaces on the screen by porting LVGL

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

The display chip itself does not support hardware rotation. If rotation is needed, it can be achieved through software. You can find the macro definition #define EXAMPLE_Rotate_90 in main file and uncomment this macro definition. Software rotation performance is not as good as hardware rotation

#define EXAMPLE_Rotate_90

Result demonstration

The LVGL demo has high requirements for RAM and ROM, so it is necessary to configure the demo according to the requirements of environment setup, and after the program is flashed, the running effect of the device is as follows:

For more learning and use of LVGL, please refer to LVGL official documentation

08_LVGL_SDIMG

Demo description

Store the images in png, jpg, and bmp formats on the TF card, then read the images from the TF card and display them on the LVGL interface
Note :
- The images need to have a unified resolution of 320 x 240
- BMP images must be converted to RGB565 format

Hardware connection

Connect the board to the computer using a USB cable

Code analysis

The display chip itself does not support hardware rotation. If rotation is needed, it can be achieved through software. You can find the macro definition #define EXAMPLE_Rotate_90 in main file and uncomment this macro definition. Software rotation performance is not as good as hardware rotation

#define EXAMPLE_Rotate_90

Result demonstration

Create a new directory Test under the TF card, put the required pictures into the directory, then insert the TF card into the board, power on normally, and the operation effect of the device is as follows:

Clicking Scan IMG will scan the image files in the Test directory. The scan results are shown in the figure:

Click on the corresponding image file name to jump to the corresponding image, as shown in the figure:

09_FactoryProgram

Demo description

Comprehensive project, test the onboard function, this demo needs to pay attention to the version of IDF, V5.2.0 or above may not be able to scan the surrounding wifi. If you need to test, you can use the lower version of the compilation or use the BIN firmware we provide

Hardware connection

Use a USB cable to connect the board to the computer (the display effect is default to software rotation by 90 degrees. If you don't need it, you can find the #define EXAMPLE_Rotate_90 macro definition in the main file and comment it out)

Result demonstration

Swipe left or right to switch pages, first display RGB colors every 1.5 seconds, which can be used to observe if there are any issues with the screen

After the RGB is displayed, it will automatically jump to the clock interface

Swipe left on the interface, you can see that this page contains some built-in hardware information

Swipe left again, you can see that the interface is a functional interface

You can click on the WIFI icon to enter the WIFI test interface, then click the Scan button to scan the surrounding WIFI
Click Exit to return to the previous interface, then click the BLE flag to enter the BLE test interface, and then click the Scan button to scan the surrounding BLE

The final interface is for backlight adjustment, where you can slide the slider to adjust the backlight brightness

Resources

Schematic Diagram

Schematic diagram

Demo

ESP32-S3-Touch-AMOLED-1.43 Demo

Datasheets

ESP32-S3

Other Components

Software Tools

Arduino

VScode

VScode official website

FAQ

Question: After the module downloads the demo and re-downloads it, why sometimes it can't connect to the serial port or the flashing fails?

Answer:

Long press the BOOT button, press RESET at the same time, then release RESET, then release the BOOT button, at this time the module can enter the download mode, which can solve most of the problems that can not be downloaded.

Question: Failed to set up the VSCode environment?

Answer:

First consider the network issue, try switching to another network

Question: Error when compiling an Arduino program?

Answer:

Check if the Arduino IDE -> Tools is correctly configured

Question: Is it stuck when sliding pictures displayed?

Answer:

Modify LVGL display cache to the full screen size
Modify the LV_IMG_CACHE_DEF_SIZE option in the configuration to 1000 to achieve some optimization

Question: Can't display Chinese?

Answer:

Basic Chinese can be displayed, but if it is a rare character, it cannot be displayed
You can transcode the required rare characters through the transcoding software, and then add them to the project font library

Question: How to deal with the first compilation of the program being extremely slow?

Answer:

It's normal for the first compilation to be slow, just be patient

Question: How to handle the display "waiting for download..." on the serial port after successfully ESP-IDF flashing?

Answer:

If there is a reset button on the development board, press the reset button; if there is no reset button, please power it on again

Question: What should I do if I can't find the AppData folder?

Answer:

Some AppData folders are hidden by default and can be set to show.
English system: Explorer->View->Check "Hidden items"
Chinese system: File Explorer -> View -> Display -> Check "Hidden Items"

Question: How do I check the COM port I use?

Answer:

Windows system:

①View through Device Manager: Press the Windows + R keys to open the "Run" dialog box; input devmgmt.msc and press Enter to open the Device Manager; expand the "Ports (COM and LPT)" section, where all COM ports and their current statuses will be listed.
②Use the command prompt to view: Open the Command Prompt (CMD), enter the "mode" command, which will display status information for all COM ports.
③Check hardware connections: If you have already connected external devices to the COM port, the device usually occupies a port number, which can be determined by checking the connected hardware.

Linux system:

①Use the dmesg command to view: Open the terminal.
①Use the ls command to view: Enter ls /dev/ttyS* or ls /dev/ttyUSB* to list all serial port devices.
③Use the setserial command to view: Enter setserial -g /dev/ttyS* to view the configuration information of all serial port devices.

Question: Why does the program flashing fail when using a MAC device?

Answer:

Install MAC Driver and flash again.

Question: How to use SquareLine Studio to design interfaces?

Answer:

Please refer to SquareLine Studio tutorial

Support

Technical Support

If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. Please be patient as we make every effort to help you to resolve the issue.
Working Time: 9 AM - 6 PM GMT+8 (Monday to Friday)

Submit Now

ESP32-S3-Touch-AMOLED-1.43

Overview

Introduction

Features

Onboard Resources

Interfaces

Dimensions

Without case version

With case version

AMOLED Specifications

Usage Instructions

Development Tools

Arduino IDE

ESP-IDF

Components Preparation

Working with Arduino

Environment Setup

Download and Install Arduino IDE

Install ESP32 Development Board

Install Library

Run the First Arduino Demo

New Project

Compile and Flash Demos

Demo

Arduino Project Parameter Setting

01_ADC_Test

02_I2C_PCF85063

03_I2C_QMI8658

04_SD_Card

05_WIFI_AP

06_WIFI_STA

07_LVGL_Test

Working with ESP-IDF

Environment Setup

Download and Install Visual Studio

Install Espressif IDF Plugin

Run the First ESP-IDF Demo

New Project

Create Demo

Modify COM Port

Modify Driver Object

Introduction to Other Status Bar Functions

Compile, Flash and Serial Port Monitor

Use the IDF Demos

Open in the software

Open from Outside the Software

ESP-IDF Project Details

Demo

01_ADC_Test

02_I2C_PCF85063

03_I2C_QMI8658

04_SD_Card

05_WIFI_AP

06_WIFI_STA

07_LVGL_Test

08_LVGL_SDIMG

09_FactoryProgram

Resources

Schematic Diagram

Demo

Datasheets

ESP32-S3

Other Components

Software Tools

Arduino

VScode

Other Resource Links

FAQ

Support