8inch DSI LCD (C)

From Waveshare Wiki
Jump to: navigation, search
8inch DSI LCD (C)
8inch-dsi-lcd-c-1.jpg

8inch capacitive Touch Screen LCD for Raspberry Pi, DSI Interface
{{{name2}}}

{{{name3}}}

{{{name4}}}

{{{name5}}}

{{{name6}}}

Feature

  • 8-inch DSI touch screen with 10-point capacitive touch.
  • IPS display panel with a hardware resolution of 1280x800.
  • Adopts optical bonding technique and clearer imaging.
  • Toughened glass touch panel with 6H hardness.
  • Supports Pi5/4B/CM4/3B+/3A+/3B/CM3+/CM3.
  • Drive LCD directly through Raspberry Pi's DSI interface with a refresh rate of up to 60Hz.
  • When working with Raspberry Pi, it supports Bookworm/Bullseye/Buster.
  • Support backlight adjusted by software.

Video

[[1]]

Hardware Connection

Working with Pi4B/3B+/3B/3A+

1. Connect the DSI interface of the LCD to the DSI interface of the Raspberry Pi board using the FPC cable.
2. Install the Raspberry Pi with its back facing downwards onto the display board, and connect it to the 5V power supply and I2C communication via the 4-pin header.
Installation effect as shown below:
8inch DSI LCD C RPI.jpg

Working with Pi5/CM4/CM3+/CM3

1. Use the "DSI-Cable-12cm" ribbon cable to connect the LCD screen's DSI interface to the Raspberry Pi's 22PIN DSI1 interface.
2. Install the Raspberry Pi with its back facing downwards onto the display board, and connect it to the 5V power supply and I2C communication via the 4-pin header.
Installation effect as shown below:
8inch-DSI-LCD-C-pi53.jpg

Software Setting

For Bookworm and Bullseye System

  • 1. Insert the TF card into the PC, download and use Raspberry Pi Imager to program the corresponding image.

Pan-Tilt Camera WRITEIMAGE01.png

  • 2. After programming the image, open the "config.txt" file located in the root directory of the TF card. Add the following code at the end of config.txt, save the file and safely eject the TF card.
Note: As Pi 5/CM4/CM3+/CM3 has two MIPI DSI interfaces, please ensure to use the correct DSI interface and command. DSI1 is recommended by default.
dtoverlay=vc4-kms-v3d
#DSI1 Use
dtoverlay=vc4-kms-dsi-waveshare-panel,8_0_inch
#DSI0 Use
#dtoverlay=vc4-kms-dsi-waveshare-panel,8_0_inch,dsi0
  • 3. Insert the TF card into the Raspberry Pi, power on the Raspberry Pi, and wait for a few seconds for the display. Once the system boots up, you should be able to interact with it normally, including touchscreen functionality.

For Buster System

Method 1: Install Driver Manually

1. Download the image of the newest version Raspberry Pi, download the compressed file to the PC, and extract the .img file.
2. Connect the TF card to PC, use SDFormatter to format TF card.
3. Open Win32DiskImager software, select the system image prepared in step 1 and click write to burn the system image.
4. After the programming is completed, connect the TF card to the Raspberry Pi, start the Raspberry Pi, and log in to the terminal of the Raspberry Pi (you can connect the Raspberry Pi to an HDMI display or log in remotely with ssh).

#Step 1: Download and enter the Waveshare-DSI-LCD driver folder
git clone https://github.com/waveshare/Waveshare-DSI-LCD
cd Waveshare-DSI-LCD
 
#Step 2: Enter "uname --all" in the terminal to view the kernel version and "cd" to the corresponding file directory
#6.1.21 then run the following command
cd 6.1.21
 
#Step 3: Please check the bits of your system, enter the 32 directory for 32-bit systems, and enter the 64 directory for 64-bit systems
cd 32
#cd 64
 
#Step 4: Enter your corresponding model command to install the driver, pay attention to the selection of the I2C DIP switch
#8inch DSI LCD (C) 1280×800 driver:
sudo bash ./WS_xinchDSI_MAIN.sh 80C I2C0
 
#Step 5: Wait for a few seconds, when the driver installation is complete and no error is prompted, restart and load the DSI driver and it can be used normally
sudo reboot

Note: The above steps need to ensure that the Raspberry Pi can be connected to the Internet normally.
5. Wait for the system to restart, it will be able to display and touch normally.

Method 2: Program Pre-installed Image

1. Select your corresponding Raspberry Pi version image, download and decompress it as ".img" file.
Raspberry Pi 4B/CM4 version download: Waveshare DSI LCD - Pi4 pre-install image
Raspberry Pi 3B/3B+/CM3 version download: Waveshare DSI LCD - Pi3 pre-install image
2. Connect the TF card to the PC and use SDFormatter to format the TF card.
3. Open Win32DiskImager software, choose the system image prepared in the first step, and then click "write" to write the system image.
4. After the programming is finished, open the config.txt file in the root directory of the TF card, add the following code under [all], save and eject the TF card safely.

dtoverlay=WS_xinchDSI_Screen,SCREEN_type=8,I2C_bus=10
dtoverlay=WS_xinchDSI_Touch,invertedx,swappedxy,I2C_bus=10

5. Connect the TF card to the Raspberry Pi, and start the Raspberry Pi, wait for about 30 seconds to display and touch normally.

Buster System Notices

1. Update the system and run the following commands:

sudo apt-get update
sudo apt-get full-upgrade

Note: After updating the system, some diver files installed before may be covered, and you need to install the driver again so that it can display normally.
2. Replace the main board.
If the driver installed was for the Raspberry Pi 4 Model B and the user decides to change the mainboard, for example, change to the Raspberry Pi 3 Model B+, it may result in the display screen not showing properly.
This is because the Pi 4 and Pi 3 require loading different driver files. To ensure proper display functionality on the new mainboard, the user needs to reinstall the drivers according to the instructions #For Buster System.

Backlight Control

WaveShare provides the corresponding demo for the application (only supports Bookworm and Bullseye systems). Users can install it by the following commands:

wget https://files.waveshare.com/upload/f/f4/Brightness.zip
unzip Brightness.zip
cd Brightness
sudo chmod +x install.sh
./install.sh

After installation, you can open it: Menu -》Accessories -》Brightness:

43H-800480-IPS07.GIF

In addition, you can also input the following commands to control the backlight brightness in the terminal:

echo X | sudo tee /sys/class/backlight/*/brightness

X indicates any number from 0 to 255. 0 means the backlight is the darkest, and 255 means the backlight is the brightest. For example:

echo 100 | sudo tee /sys/class/backlight/*/brightness
echo 0 | sudo tee /sys/class/backlight/*/brightness
echo 255 | sudo tee /sys/class/backlight/*/brightness

Sleep Mode

Run the following commands on the Raspberry Pi terminal, and the screen can enter the sleep mode:

xset dpms force off

Disable Touching

At the end of the config.txt file, add the following commands corresponding to disabling touch (the config file is located in the root directory of the TF card, and can also be accessed through the command: sudo nano /boot/config.txt):

disable_touchscreen=1

Note: After adding the command, it needs to be restarted to take effect.

Bookworm display rotation

GUI interface rotation

  • 1. Open the "Screen Configuration" application;

DSI-LCD-Bookworm-Rotate-01.png

  • 2. Go to "Screen" - > "DSI-1" - > "Touchscreen" and check "6-0038 generic ft5x06(79)"

DSI-LCD-Bookworm-Rotate-02.png

  • 3. Click "Apply" and close the current window. Restart according to the pop-up prompt, and then touch screen select Done.

DSI-LCD-Bookworm-Rotate-03.png
DSI-LCD-Bookworm-Rotate-05.png

  • 4.Go to "Screen" -> "DSI-1" -> "Orientation", check the direction you need to rotate, and finally click "Apply" to complete the display and touch synchronous rotation.

DSI-LCD-Bookworm-Rotate-04.png -->
Note: Only the Bookworm system supports the above synchronization rotation method. For the Bullseye and Butser systems, manual separate settings for touch rotation are required after displaying the rotation.

lite version display rotation

  • 1. Need to modify the /boot/cmdline.txt file:
sudo nano /boot/cmdline.txt
  • 2. At the beginning of the cmdline.txt file, add the command for displaying the rotation angle: (Please note, this command needs to be on the same line, with each command separated by a space.)
video=DSI-1:800x480M@60,rotate=90

Change the display rotation angle by modifying the rotate value to 90, 180, or 270.

  • 3. Save and restart
sudo reboot

Bullseye/Buster Display Rotation

  • 1. Open "Screen Configuration" application:

DSI-LCD-Bullseye-Rotate-02.png

  • 2. Enter "Screen"->"DSI-1"->"Orientation", select the rotation direction, and then click on "Apply" to complete the display rotation.

DSI-LCD-Bullseye-Rotate-03.pngDSI-LCD-Bullseye-Rotate-04.png

Bullseye/Buster Touch Rotation

sudo nano /boot/config.txt
#Change the command for the touch rotation angle at the end of the config.txt file, reboot it to take effect (the command for 0° touch direction exists by default) 
#0°:
dtoverlay=WS_xinchDSI_Touch,invertedx,swappedxy
#90°:
dtoverlay=WS_xinchDSI_Touch,invertedx,invertedy
#180°:
dtoverlay=WS_xinchDSI_Touch,invertedy,swappedxy
#270°:
dtoverlay=WS_xinchDSI_Touch

lite Version Rotation

sudo nano /boot/cmdline.txt
#Add the command to display the rotation angle at the beginning of the cmdline.txt file, save and reboot to take effect
#Display rotates 90°
video=DSI-1:1280x800M@60,rotate=90
#Display rotates 180°
video=DSI-1:1280x800M@60,rotate=180
#Display rotates 270°
video=DSI-1:1280x800M@60,rotate=270

Resource

3D Drawing

2D Drawing

Pre-installed image

FAQ

 Answer:

Using a 5V power supply, the working current of the backlight on is about 520mA, and the working current of the backlight off is about 150mA.

{{{5}}}


 Answer:

Replace the custom image with the image in this directory /usr/share/plymouth/themes/pix/splash.png.

{{{3}}}
{{{4}}}

{{{5}}}


 Answer:

The power supply is 5V 500mA.

{{{5}}}


Support



Technical Support

If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. Please be patient as we make every effort to help you to resolve the issue.
Working Time: 9 AM - 6 PM GMT+8 (Monday to Friday)