10.1HP-CAPLCD Monitor

From Waveshare Wiki
Jump to: navigation, search

Introduction

Overview

The 10.1HP-CAPLCD Monitor is a small, high-resolution, wide-color gamut general-purpose capacitive touch monitor compatible with most standard HDMI devices. Comes with an aluminum alloy case, toughed glass panel, excellent display performance, and smooth multi-touch effect.

Features

  • 10.1-inch wide color gamut IPS panel, 1280 x 800 hardware resolution.
  • Supports standard HDMI and full-featured Type-C display signals
  • 10-point capacitive touch, toughened glass panel with 6H hardness.
  • Adopts optical bonding technique for better display.
  • Supports Raspberry Pi OS / Ubuntu / Kali and Retropie when used with Raspberry Pi.
  • Supports Windows 11 / 10 / 8.1 / 8 / 7 when used as a computer monitor.
  • Multi-language OSD menu support (for power control, adjusting brightness/contrast, etc.)
  • Supports HDMI/Type-C audio output, onboard 3.5mm headphone jack, and 4PIN speaker jack.

10.1HP-CAPLCD Monitor01.png

Specification

Item Description Unit
Model 10.1HP-CAPLCD Monitor /
Dimensions 10.1 Inch
Viewing Angle 178 Deg
Resolution 1280 x 800 Pixels
Overall Dimensions 241.00(H) × 149.00(V) × 11.80(D) mm
Display Dimensions 228.6(H) × 143.0(V) mm
Display Area 135.36(H) × 216.58(V) mm
Pixel Pitch 0.1175(H) x 0.1088(V) mm
Color Gamut 82% NTSC
Max. Brightness 350 cd/m²
Contrast 800:1 /
Backlight Adjustment OSD Menu /
Refreshing Rate 60 Hz
Display Interface Standard HDMI Interface /
Power Port 5V Type-C /
Power Consumption 4 Watt
Weight 809 g

Electrical Parameters

Parameter Min. Value Standard Value Max. Value Unit Note
Input Voltage 4.75 5.00 5.25 V Note 1
Input Current 750 800 TBD mA Note 2
Operating Temperature 0 25 60 Note 3
Storage Temperature -10 25 70 Note 3

•Note 1: Input voltage exceeding the maximum value or improper operation may cause permanent damage to the device.
•Note 2: The input current should be ≥750mA, otherwise it will lead to start-up failure or abnormal display, and a long time in an abnormal state may cause permanent damage to the device.
•Note 3: Please do not put the display in a high temperature and high humidity storage environment for a long time, the display needs to work within the limit value, otherwise it will be possible to damage the display.

EDID Sequence Parameters

If the system of the main control board can automatically identify the EDID for display, there is no need to set the relevant timing parameters additionally.

Otherwise, you can refer to the following EDID settings:

Pixel Clock H Addressable H Blanking V Addressable V Blanking H Front Porch H Sync Width V Front Porch V Sync Width H Image Size V Image Size H Border V Border
77.00 1280 232 800 56 160 32 20 6 294 165 0 0

Onboard Interface

8DP-CAPLCD10.jpg

User Manual

Working with PC

Support Windows 11/10/8.1/8/7

How to Use

  1. Connect the Touch port of the LCD to the USB interface of the PC, and Windows will automatically identify the touch function.
  2. Connect the LCD's HDMI interface to the PC's HDMI interface, and Windows will automatically identify the display function.
  • Note:
  • Some PCs do not support HDMI devices plug-and-play, usually after rebooting the system can be used normally.
  • If the power supply of the USB interface is insufficient, the LCD will flicker, after connecting the external 5V 1A power adapter to the LCD's Power interface, it can be restored to normal use.

Windows Software Brightness Adjustment

  • 1. Download and install DDC/CI applications, such as the open-source Twinkle Tray.
  • 2. Open the software dimming icon, it will recognize the Waveshare monitor and adjust the monitor backlight brightness by sliding the scroll bar.

8HP-CAPLCD Monitor04.png

  • 3. You can also enter the DDC/CI application settings screen to enable contrast adjustment, volume adjustment, and other functions.

8HP-CAPLCD Monito03.png

Windows Touch Calibration

Take Windows 10 as an example:

  • 1. Enter the Windows setting of the system, type in the search bar, and click "Calibrate the screen for pen or touch input" (as shown in the picture below):

Win10 touch011.png

  • 2. Click "Setup" in the pop-up "Tablet PC Settings" interface:

Win10 touch02.png

  • 3. The following text prompt will appear on the screen. Please tap the touch screen with your finger, and the computer will recognize it as a touch screen.
【Note】If the touch screen is blank, press the "Enter" key, and the text prompt will switch to the touch screen. (The screen which displays the text prompt will be used as a touch screen!)

Win10 touch03.png

Working with Raspberry Pi

Hardware Connection

  1. Connect the Touch port to the USB interface of the Raspberry Pi.
  2. Connect the HDMI interface to the HDMI interface of the Raspberry Pi.

8HP-CAPLCD Monitor05.jpg

Software Setting

Raspberry Pi OS / Ubuntu / Kali and Retropie systems are supported for Raspberry Pi.
When the LCD works on these systems of Raspberry Pi, the resolution must be set manually, otherwise, it will result in incorrect display resolution and affect the experience.

1. Please download the newest image from the Official Raspberry Pi website.
2. Download the compressed file on the PC and unzip it to get the .img file.
3. Connect the TF card to the PC and use SDFormatter to format the TF card.
4. Open Win32DiskImager, choose the image prepared in the first step, and click "Write" to program the system image.
5. After programming, open the config.txt file in the root directory of the TF card and enter the following codes at the end of config.txt. Then, save and safely eject the TF card.

hdmi_group=2
hdmi_mode=87
hdmi_cvt 1280 800 60 6 0 0 0
hdmi_drive=1

6. Insert the TF card into the Raspberry Pi, power up the Raspberry Pi, wait for a few seconds normally and then it will display normally.

Linux Software Brightness Adjustment

Using the DDC/CI program, here is an example of the ddcutil tool.

#Install ddcutil tool:
sudo apt-get install ddcutil -y
#Detection support for DDC/CI monitors:
sudo ddcutil detect
#Adjust the monitor brightness, <value> should be modified to 0-100 value
sudo ddcutil setvcp 10 <value>

For more information about ddcutil function commands, please check http://www.ddcutil.com/commands/.

One Cable Connection

Using the matching dual-plug Type-C cable, connect the monitor's DISPLAY&TOUCH connector to the master's full-featured Type-C connector. Wait for a few seconds to enter the display interface.
8HP-CAPLCD Monitor 06.jpg
Note: Please make sure your main control supports a full-featured Type-C interface and your phone needs to support the wired projection function.

Dimensions

10.1HP-CAPLCD Monitor09.jpg

Resource

Support



Technical Support

If you need technical support or have any feedback/review, please click the Submit Now button to submit a ticket, Our support team will check and reply to you within 1 to 2 working days. Please be patient as we make every effort to help you to resolve the issue.
Working Time: 9 AM - 6 PM GMT+8 (Monday to Friday)